manualshive.com logo in svg

Samsung Xpress C1810 series, Service Manual, Page: 27 / 120

Share
Download
Samsung Xpress C1810 series Service Manual Download Page 27

2. Product specification and description

2.2.5. Hardware configuration

Xpress C1810 series Electrical Circuit System consists of the following:

•

Main board (System board)

•

OPE board

•

SMPS board

•

HVPS board

Diagram of Xpress C1810 series Electrical Circuit

Xpress C1810 series has a system board of integrated engine controller and video controller.

The engine controller controls all modules required to print, that is, LSU, HVPS/SMPS, Fuser, Motor etc. It communicates
with the video control block inside CPU for printing. And it has the interface for all video sync signal to print out
the video data.

The video controller receives print data from the host through network or USB Port and receives copy data from the scan
controller. It takes this information and generates printable video bitmap data.

The main board is adopted 533 MHz C3N CPU that is integrated with engine/ video/ scan controller. It uses DDR3
256MByte.

Copyright© 1995-2017 SAMSUNG. All rights reserved.

2-17

Summary of Contents for Xpress C1810 series

























































































































Reviews:

No comments