background image

- 12 -

INSTALLATION & MAINTENANCE

The User’s Manual is for common use.
Make use of the User’s Manual depending upon your washing machine model.

ENVIRONMENT

Leave some space 

Maintain at least 10cm between the washer and the wall.

Place the washer on a sturdy flat surface.

If the washer is placed on an uneven or weak surface, noise or vibration occurs.
(Allowable is 1

˚

)

Adjust the legs for even placement.

Never install the washer near water.

Do not place the washer in steamy rooms or where  the washer is directly exposed to
rain.Moisture may destroy the electrical insulation causing an electrical shock hazard.

Avoid direct sunlight or heaters.

As plastic and electrical components are affected by direct heat,never place the washer
near furnaces, boilers, etc. Do not place under direct sunlight.

LEVELLING

(If the washer is not leveled with the ground, it makes the machine tremble more or be out of
order. So, make sure that the washer is leveled properly. )

SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING THE POSITION
OF THE WASHING TUB.

• Open the lid of the machine, pour water into the tub up to the level just

below the pulsator, and adjust the legs so that the pulsator is positioned at
the center of the water as shown in the figure.

• Place the machine more than 10cm away from the wall.
• Adjust the legs on feet for levelling .

1. Adjust the side horizontally first and the front in

same direction 

next.

2. If the thread is not within the limit, adjust the height of the

legs.

HOW TO ASSEMBLE THE LEGS

1. Check the 4 Legs.(Front-right. Front-left. Rear-right. Rear-left)
2. Lay down the Washing Machine to the front.
3. Insert the hook of leg in to the square hole 

of base.

4. Push the leg to the arrow direction to “Click”.
5. Finaly fix the legs on the base

with screw like a figure.

CONNECTING THE WATER SUPPLY HOSE

1. Remove the adaptor from the water supply hose.

2. First,using a "+" type screw driver, loosen the four screws on

the adaptor. Next,take the adaptor and turn the part(b) in the
direction of the arrow for about 5mm gap between them.

3. Connect the adaptor to the water tap and tighten the screws

firmly. Then, turn the part (b) in the direction of the arrow by
fastening.

4. After Pulling down the part (c) of  the water supply hose,

connect the water supply hose to the adaptor. When the part
(c) is released, the hose is automatically connected to the
adaptor making a 'click' sound.

5. Connect the other end of the  water supply hose to the inlet

water valve at the back or top  of the washer in the direction of
the arrow tightly.
Check if there is any leakage.

After completing connection, if water leaks from the hose,then
repeat the same steps. Use the most conventional type of faucet
for water supply. In case the faucet is square or too big, remove
the spacing ring before inserting the faucet into the adaptor.

a

b

c

Lock

Loosen

1

2

Base

Hole

Hook

Screw

Summary of Contents for WA1351S

















Reviews: