background image

English 

English

 _ 3

safety information

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION

:  TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE 

PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of electric shock is 
present within this unit.

This exclamation point symbol is intended to alert the user to the presence of 
important operating and maintenance (servicing) instructions in the literature 
accompanying the appliance.

WARNING

To reduce the risk of fi re or electric shock, do not expose this appliance to rain or moisture.

WARNING

Be sure to use only the standard adapter that is specifi ed in the specifi cation sheet.
Using any other adapter could cause fi re, electrical shock, or damage to the product.

Incorrectly connecting the power supply or replacing battery may cause explosion, fi re, electric shock, or damage to 
the product.

Do not connect multiple controllers to a single adapter. Exceeding the capacity may cause abnormal heat generation or fi re.

Securely plug the power cord into the power receptacle. Insecure connection may cause fi re.

When installing the controller, fasten it securely and fi rmly. The fall of controller may cause personal injury.

Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers fi lled with water on top of the 
controller. Doing so may cause personal injury due to fi re, electric shock, or falling objects.

Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fi re or electric shock.

If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the 
power source and contact the service center. Continued use in such a condition may cause fi re or electric shock.

If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in 
any way. (SAMSUNG is not liable for problems caused by unauthorized modifi cations or attempted repair.)

. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fi re or electric shock.

CAUTION

Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive 
vibration or magnetic interference.

Do not install in a location subject to high temperature (over 50°C), low temperature (below -25°C), or high humidity. 
Doing so may cause fi re or electric shock.

If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it.

Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause fi re or damage 
to the product.

Keep out of direct sunlight and heat radiation sources. It may cause fi re.

Install it in a place with good ventilation.

Avoid aiming the controller directly towards extremely bright objects such as sun.

Apparatus shall not be exposed to dripping or splashing and no objects fi lled with liquids, such as vases, shall be 
placed on the apparatus.

The Mains plug is used as a disconnect device and shall stay readily operable at any time.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

1.

2.

3.

4.

5.

6.

7.

8.

9.

SAFETY INFORMATION

Summary of Contents for SSA-R2001V



















Reviews: