Samsung SL-M4580FX Service Manual Download Page 199

Page: 199 / 252

4. Troubleshooting

► Error Code

M1–3122

► Error message

Tray 1 cassette is pulled out. Insert it properly.

► Symptom

Tray1 is not installed properly.

► Troubleshooting method

1) Install the tray1. If the tray1 is already installed, remove and reinstall it.

2) Check if the harness connection for cassette detection is normal. Reconnect it. If the harness is defective, replace it.

3) Check if the cassette detection sensor(

JC34-00001A

) is defective, replace it.

► Error Code

M1–4111

► Error message

Tray Failure: #M1-4111. Pull tray 1 out and insert it. Call for service if the problem persists.

► Symptom

The paper has jammed in the path or can’t be fed.

► Troubleshooting method

1) Check if the pick up/ forward/ retard roller(

JC97–02259A

) are contaminated or worn out. Replace the defective

roller.

2) Check the feed drive unit for cassette lifting.

•

Check if the gear is worn out or broken.

•

Check if the DC motor is working normally.

4-96

Summary of Contents for SL-M4580FX






















































































































































































































































Search results

Summary of Contents for SL-M4580FX

Reviews:

Related manuals for SL-M4580FX

Brands by name

Popular brands

Samsung SL-M4580FX, Service Manual

Search results

Summary of Contents for SL-M4580FX

Reviews:

Related manuals for SL-M4580FX

Brands by name

Popular brands