Samsung SGH-Z720M Service Manual Download Page 21

Page: 21 / 88

SAMSUNG Proprietary-Contents may change without notice

Exploded View/Disassembly&Assembly Instructions

5-6

This Document can not be used without Samsung's authorization

Screw cover Removal

Remove the left and right screw covers.

Slide Ass'y Screw Removal

Push up the slide a little bit.

Remove the slide Ass'y screw 2 points.

Slide Lower Screw Removal

1. Slide up only half of 3*4 Key part like the

picture.

2. Remove two unconcealed screws

Slide Ass'y & Front Unlocking

Unlock the 4 locking points with an unlocking
stick.

Slide Ass'y & Front Separation

Separate the slide upper and the slide lower

after unlocking.

Front Hole Adjustment

Adjust the slide lower hole to the front hole
to draw out from the hole.

Front screw 2 point

Summary of Contents for SGH-Z720M

























































































Search results

Summary of Contents for SGH-Z720M

Reviews:

Related manuals for SGH-Z720M

Brands by name

Popular brands

Samsung SGH-Z720M, Service Manual

Search results

Summary of Contents for SGH-Z720M

Reviews:

Related manuals for SGH-Z720M

Brands by name

Popular brands