manualshive.com logo in svg

Samsung SF-330 Series, Service Manual, Page: 24 / 24

Share
Download
Samsung SF-330 Series Service Manual Download Page 24

 

 

 

 

Page 24 

 

SF-330 Series Graphic Print Bar 
Service Guide 

 

Samsung Electronics Confidential 

 Copyright Samsung Electronics Company 2002 

SF-330 Series Graphic Print Bar Service Guide

Revision 1.0; 23-Jul-02

 

 

Media Specifications 
 

The following recommended media specifications apply to the media   used in the Graphic Print 
Bar, and is a general specification for commonly available good quality plain paper used in 
copiers and fax type products. 
 

Plain Paper Specifications: 

 

Weight:                             22lb or 83 g/m2 
Finished Dimensions:      8.5"x11" or 216x279mm (5.44 kg/M) 
Grain:                               Long grain 
Moisture content:             not specified  
Brightness:                       92 
Type of packaging wrap:  Multi-layer packaging wrap using paper and an exterior 
                                          polymer for shock and moisture protection  
Type:                                 Cut Sheet 
 

Other Paper Specifications 

Note: Except for opacity, the following international paper specs would not  
        normally be available to consumers purchasing paper from a supplier. 

 
International Paper Target Specs: 
Ash(Dry End): 16.50 
Opacity: 90 
Caliper: 4.30 
Formation: 37 
Porosity Avg: 15 
Smoothness Bottom Avg: 140 
Smoothness Top Avg: 135 
Taber Stiff CD Avg: 1.50 
Taber Stiff MD Avg: 2.90

 

 

 

Summary of Contents for SF-330 Series

























Reviews:

No comments