Samsung S27H850QF series User Manual Download

Page: 48 / 57

Source Detection

Select either

Auto

Manual

as the method to recognize input signal.

―

This menu is not available when the

MST

mode is selected for

DP OUT

Key Repeat Time

Control the response rate of a button when the button is pressed.

Acceleration

1 sec

, or

2 sec

can be selected. If

No Repeat

is selected, a command responds only once

when a button is pressed.

Power LED On

Configure the settings to enable or disable the power LED located at the lower part of the product.

•

Working

: The power LED is on when the product is turned on.

•

Stand-by

: The power LED is on when the product is turned off.

Reset All

Return all the settings for the product to the default factory settings.

Information

View the current input source, frequency and resolution.

Summary of Contents for S27H850QF series


























































Search results

Summary of Contents for S27H850QF series

Reviews:

Related manuals for S27H850QF series

Brands by name

Popular brands

Samsung S27H850QF series, User Manual

Search results

Summary of Contents for S27H850QF series

Reviews:

Related manuals for S27H850QF series

Brands by name

Popular brands