background image

Confidential

 

 

Preface 

RFV01U-D1A Installation Manual   v2.0 

 

 xiii 

Copyright © 2017, All Rights Reserved.

 

or in conductive bags. 

 

All tools must be discharged to ground before use. 

 

The anti-static wrist strap and cord must be checked at regular intervals for 
their suitability for use. 

Grounding 

To comply with EN 60950, the equipment must be connected to a safety 
grounding point via a permanent link. Grounding points are located on the product 
for this purpose. Always connect the ground cable before fitting other cables. The 
product must remain grounded continuously unless all connections to the power 
supply and data network are all removed. 

If equipment is grounded through a cabinet or rack, make sure it is done so 
properly according to the installation instructions. 

Power Supply Connection 

The equipment is designed to be powered from a -48 V DC supply. Power 
connections and installation of associated wiring must be carried out by a suitably 
qualified technician. 

Only devices that comply with all relevant national safety requirements should be 
connected to the unit’s power supply inlets. Other usage will invalidate any 
approval given to this equipment. 

Connection of this equipment to devices that are not marked with all relevant 
national safety requirements may produce hazardous conditions on the network. 

When the power supply is obtained by a rectifier/safety isolation transformer, the 
supply must meet the requirements of EN 60950 providing double/reinforced 
insulation between hazardous voltages and SELV/TNV circuits. Any battery must 
be separated from hazardous voltages by reinforced insulation. 

Indirect Connection 

Before indirectly connecting any equipment to another device through a shared 
power supply, ALWAYS seek advice from a competent engineer. 

Devices that are not marked according to the relevant national safety standards 
may produce hazardous conditions on the network. 

Product Disposal 

To reduce the environmental impact of products, Samsung has joined WEEE 
compliance activities. 

The WEEE symbol on the product indicates that the product is covered by the 
European Directive 2002/96/CE for the disposal of Waste Electrical and Electronic 
Equipment (WEEE). This means that the product should be disposed of separately 
from the municipal waste stream via designated collection facilities appointed by 

Summary of Contents for RFV01U-D1A





























































Reviews: