background image

Wiring the Mains Power Supply Plug (UK Only)

IMPORTANT NOTICE

The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on 
the pin face of the plug and, if it requires replacing, a fuse approved to BSI1362 of the same rating must be used.
Never use the plug with the fuse cover omitted if the cover is detachable. If a replacement fuse cover is required, it must be of 
the same colour as the pin face of the plug. Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you 
should obtain a suitably approved extension lead or consult your dealer for assistance. However, if there is no alternative but to 
cut off the plug, remove the fuse and then safely dispose of the plug.
Do NOT connect the plug to a mains socket as there is a risk of shock hazard from the bared flexible cord.

IMPORTANT

The wires in the mains lead are coloured in accordance with the following code:
BLUE - NEUTRAL BROWN - LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows : 
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire 
coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.

WARNING:

DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL, WHICH IS MARKED WITH THE 
LETTER E OR BY THE EARTH SYMBOL , OR COLOURED GREEN OR GREEN AND YELLOW.

Warranty Card

UNITeD KINGDOM

This Samsung product is warranted for a period of twelve (12) months from the original date of purchase, against defective 
materials and workmanship. In the event that warranty service is required, you should return the product to the retailer from 
whom it was purchased. However, Samsung Authorised Dealers and Authorised Service Centres in other EC Countries will 
comply with the warranty on the terms issued to purchasers in the country concerned. In case of difficulty, details of our 
Authorised Service Centres are available from:

Samsung Electronics U.K. Ltd.

Customer Care Centre

PO Box 17243

Edinburgh, EH11 4YB

United Kingdom

Tel: 0845 SAMSUNG (7267864) (UK & Northern Ireland)

Tel: 0818 717 100 (EIRE Only)

Fax: +44 0845 650 8080

Web : www.samsung.com

WARRANTY CONDITIONS

1.

 

The warranty is only valid if, when warranty service is required, the warranty card is fully and properly completed and 
is presented with the original invoice or sales slip or confirmation, and the serial number on the product has not been 
defaced.

2.

 

Samsung’s obligations are limited to the repair or, at its discretion, replacement of the product or the defective part.

3.

 

Warranty repairs must be carried out by Authorised Samsung Dealers or Authorised Service Centres. No re-imbursement 
will be made for repairs carried out by non Samsung Dealers and, any such repair work and damage to the products 
caused by such repair work will not be covered by this warranty.

4.

 

This product is not considered to be defective in materials nor workmanship by reason that it requires adaptation in 
order to conform to national or local technical or safety standards in force in any country other than the one for which the 
product was originally designed and manufactured.

[PC6900_UK]BN68-02807S-01Eng.indb   64

2010-05-12   오후 2:55:08

Summary of Contents for PS50C6900

































































Reviews: