background image

ENGLISH-7

02

 

INS

ta

LL

at

ION

4 .  Reassemble your wired remote controller .

•  Align the controller with the upper groove first, and insert it by turning it downward as 
    shown in the figure . 
    After assembly, check and confirm that no wires are stuck in the gap between the rear and 
    front cover .

• 

  When installing a wired remote controller by using a cable longer than 10 m(32 .80 ft), you must install the communication cable 

and the power cable separately . (Electrical interference can cause your wired remote controller to malfunction .)

•   When installing your wired remote controller on the wall, consider the size of the wire hole, and select a wire with a proper 

thickness .

•   If you install the wired remote controller by using two pieces of PVC wire, remove the 30 cm (12 inch) of the  

sheath of the cable and install it only with the two pieces of wires . (Recommended specification: AWG20)

•   Maximum distance for connecting communication and power cable : 100 m (328 ft) .

•    Screws on the PCB terminal must be tightened with less than 6N-cm tightening torque. If the tightening torque is 

greater, it may damage the screw thread. 

3 .     Using more than two screws, firmly affix the rear cover of the remote controller to the wall, and then connect the 
        communication and power cable [(F3,F4) or (3, 4)], making sure these cables have reasonable length, to the terminal at 
        the back of the cover .

F1 F2 V1 V2 F3 F4

F3 F4

10 mm(0.4 inch) or more

10 mm(0.4 inch) 

or more

10 mm(0.4 inch) or more

10 mm(0.4 inch) or more

Screw hole

Rear cover

Front cover

PCB terminal

Wire (not supplied)

  Before fixing the rear cover, secure at least  

 10 mm (0.4 inch) space of upper side, left 

     side, right side, and bottom side.

  You must fit the screws into  

 the screw holes.

Indoor unit

Wired remote 

controller

  Do not tighten the screws on the  

 PCB terminal with excessive force.

CaUtION

SOL 터치간단유선 유럽향 IM_EN_DB68-08073A-00.indd   7

2018-10-11   오후 3:35:05

Summary of Contents for MWR-SH11N





















Reviews: