Samsung Mobile WiMAX Outdoor RAS SPI-2331 System Description Download Page 41

Page: 41 / 96

CHAPTER 3. Outdoor SPI-2331 Architecture

3-8

3.2.4

I/O Connector and LED

The I/O connectors and LEDs at the top and bottom of the outdoor SPI-2331 cabinet are

described below.

Figure 3.4 I/O Connector and LED of Outdoor SPI-2331

3.2.4.1 I/O Connector Information

I/O connector(external interface) structure of the outdoor SPI-2331 is as follows:

Figure 3.5 External Interface of Outdoor SPI-2331

RF Processing

Control

Baseband

Processing

Network

Interface

ULDB

ULRB

GPSR

BACKHAUL 0

CRAFT

ANT A ANT B

ULPU

Filter

Tx power

monitoring

GPS

11.2M

TDD

UDE
UDA(2Tx/6Rx)

PWR ALM

Power

Conversion

PWR

BACKHAUL 1

GPS ANT

ANT B

ANT A

PWR PWR ALM

UDA

CRAFT

UDE BACKHAUL 1

Ground

11.2M

TDD

SYS/LINK

GPS RF

BACKHAUL 0

[Top of the Cainet]

[Bottom of the Cainet]

Summary of Contents for Mobile WiMAX Outdoor RAS SPI-2331

































































































Search results

Summary of Contents for Mobile WiMAX Outdoor RAS SPI-2331

Reviews:

Related manuals for Mobile WiMAX Outdoor RAS SPI-2331

Brands by name

Popular brands

Samsung Mobile WiMAX Outdoor RAS SPI-2331, System Description

Search results

Summary of Contents for Mobile WiMAX Outdoor RAS SPI-2331

Reviews:

Related manuals for Mobile WiMAX Outdoor RAS SPI-2331

Brands by name

Popular brands