Samsung Mobile WiMAX Outdoor RAS SPI-2331 System Description Download Page 31

Page: 31 / 96

CHAPTER 2. Overview of Outdoor SPI-2331

2-14

2.5 Interface between Systems

2.5.1 Interface Structure

The outdoor SPI-2331 interfaces with another RAS and ACR as shown in the figure below:

Figure 2.3 Structure of Outdoor SPI-2331 Interface

Interface between Outdoor SPI-2331 and MS

The outdoor SPI-2331 interfaces with an MS according to the IEEE 802.16e radio access

standard to exchange the control signal and the subscriber traffic.

Interface between Outdoor SPI-2331 and ACR

The interface between an ACR and the outdoor SPI-2331 in the same ASN is R6 and its

physical access method is FE. The R6 is the interface between ACR and RAS defined in

Mobile WiMAX NWG and is composed of signaling plane(IP/UDP/R6) and bearer

plane(IP/GRE).

Interface between Outdoor SPI-2331 and WSM

The interface between the outdoor SPI-2331 and the WSM complies with SNMPv2c or

SNMPv3c of IETF standard, SFTP and Samsung’s proprietary standard and its physical

access method is FE.

CSN

AAA

ACR

R3(Diameter, MIP, DHCP)

R1(802.16e)

SNMP,

SFTP

PCRF

WSM

Outdoor

SPI-2331

RAS

ACR

RAS

ASN

Summary of Contents for Mobile WiMAX Outdoor RAS SPI-2331

































































































Search results

Summary of Contents for Mobile WiMAX Outdoor RAS SPI-2331

Reviews:

Related manuals for Mobile WiMAX Outdoor RAS SPI-2331

Brands by name

Popular brands

Samsung Mobile WiMAX Outdoor RAS SPI-2331, System Description

Search results

Summary of Contents for Mobile WiMAX Outdoor RAS SPI-2331

Reviews:

Related manuals for Mobile WiMAX Outdoor RAS SPI-2331

Brands by name

Popular brands