Samsung ML-5200A Service Manual Download Page 27

Page: 27 / 86

4-9

Samsung Electronics

Troubleshooting

OK after

taking out and

rocking the toner

cartridge?

It is over the guaranty
life of toner cartridge.
(Check the counter
and replace it.)

When gray

pattern printing,

irregular density

persists?

PTL lamp

works OK?

Any obstacles

on the PTL lamp?

Transfer/

charge/developing

voltage drops while

printing?

Defective agitator in
the toner supplying part
of developer.
->Replace the developer.

Check if the ’guide deve
spring’ works OK and
repair/repalce.

Check high voltage
output and repair/
replace terminals/HVPS.

Replace lamp.

Clean the window of PTL.

Bad images

aroung the no image

area?

Irregualrity of toner
suppy from developer.
-> Replace developer.

Light distortion due to
the mirror ruined or
LSU’s diffused reflection.
-> Replace LSU.

YES

4-2-9 Irregular Density

Summary of Contents for ML-5200A























































































Search results

Summary of Contents for ML-5200A

Reviews:

Related manuals for ML-5200A

Brands by name

Popular brands

Samsung ML-5200A, Service Manual

Search results

Summary of Contents for ML-5200A

Reviews:

Related manuals for ML-5200A

Brands by name

Popular brands