manualshive.com logo in svg

Samsung ML-2210, Service Manual

Share
Download
Samsung ML-2210 Service Manual Download Page 88

7-16

Troubleshooting

Samsung Electronics

Service Manual

7.3.8  Defective motor operation

• Description

Main motor is faulty and paper does not feed into the printer, resulting in Jam 0'

Check and Cause

Solution

Perform EDC diagnostic code 00 to test the main motor.
1. The main motor harness or Motor PCB may be faulty.

2. The main PBA may be faulty

3. SMPS may be faulty

1. Check the motor harnesses and connectors,

replace if defective..

2. If the problem persists check and replace the main

PBA or SMPS as appropriate.

.

7.3.9 No Power 

• Description

When system power is turned the lamps on the OPE panel do not come on.

Check and Cause

Solution

1. Check if the power input and SMPS output are normal.

2. Lamps do not come on but normal start up sounds are

heard.

3. After replacing SMPS lamps do not come on and no

start up sounds are heard.

1. Replace the power supply cord or SMPS. Check

power fuse and SMPS fuses replace if necessary.

2. Check OPE connector and harness. Replace the

OPE panel or cable.

3. Replace the main PBA panel.

Summary of Contents for ML-2210



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands