Samsung ML-2210 Service Manual Download Page 7

Page: 7 / 122

2-1

Samsung Electronics

REFERENCE INFORMATION

Traninung Manual

2. Reference Information

This chapter contains the tools list, list of abbreviations used in this manual, and a guide to the
location space required when installing the printer. A definition of tests pages and Wireless
Network information definition is also included.

2.1 Tool for Troubleshooting

The following tools are recommended safe and easy troubleshooting as described in this service manual.

• DCU(Diagnostic Control Unit)

Standard : Test equipment to diagnose the Laser
printer supplied by Samsung Electronics.

•

DVM(Digital Volt Meter)

Standard : Indicates more than 3 digits.

• Driver

Standard : "-" type, "+" type (M3 long, M3 short, M2

long, M2 short).

• Tweezers

Standard : For general home use, small type.

• Cotton Swab

Standard : For general home use, for medical service.

• Cleaning Equipments

Standard : An IPA(Isopropyl Alcohol)dry wipe tissue or

a gentle neutral detergent and lint-free cloth.

• Vacuum Cleaner

• Spring Hook

Standard : For general use

• Software (Driver) installation CD ROM

Summary of Contents for ML-2210



























































































































Search results

Summary of Contents for ML-2210

Reviews:

Brands by name

Popular brands

Samsung ML-2210, Service Manual

Search results

Summary of Contents for ML-2210

Reviews:

Brands by name

Popular brands