Samsung ML-2210 Service Manual Download Page 79

Page: 79 / 122

7-7

Samsung Electronics

Troubleshooting

Service Manual

7.1.14 Stains on Back of Page

• Description

The back of the page is stained at 47 mm intervals.

Digital
Digital Pri

Digital Printer
Digital Printer
Digital Printer

Check and Cause

Solution

1. Transfer roller is contaminated.

2. Pressure roller is contaminated.

1. Perform the OPC Cleaning Mode Print 2 or

3 times. Run Self-Test to remove the
contamination from the transfer roller.

Note. Replace the transfer roller if contami-

nated severely.

2. Disassemble the fuser and clean the

H/R(Heat Roller) and P/R(Pressure roller).
Check and clean the area between the
H/R and the Thermistor. (Caution: Take
care not to deform the rollers.)

7.1.15 Blank Page Print out (1)

• Description

Blank page is printed.

Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer

Check and Cause

Solution

Bad ground contacts in OPC and/or toner
cartridge.

1. Check if the Ground-OPC or the OPC

Ground Zener diode are defective or open
circuit. (set inside left side).

2. Remove contamination of the terminals on

the toner cartridge and the unit.

7.1.16 Blank Page Print out (2)

• Description

1. Blank page is printed.
2. One or several blank pages are printed.
3. When the printer turns on, several blank pages print.

Check and Cause

Solution

1. Bad ground contacts in OPC and/or toner

cartridge.

2. Abnormal solenoid.

Try turning the power off, deleting any print
jobs in the PC print queue and then try print-
ing again.

1. See 7.1.15 above

2. Perform the engine self test using DCU

(refer to code 6) to check if the Solenoid is
normal. If the problem persists replace the
engine PBA

Summary of Contents for ML-2210



























































































































Search results

Summary of Contents for ML-2210

Reviews:

Related manuals for ML-2210

Brands by name

Popular brands

Samsung ML-2210, Service Manual

Search results

Summary of Contents for ML-2210

Reviews:

Related manuals for ML-2210

Brands by name

Popular brands