37
English
04
Advanced Featur
es
Listening through a Receiver
¦
You can listen to sound through a receiver (i.e Home Theatre) instead of the TV speaker.
1.
Select
Receiver
and set to
On
.
2.
Press the
EXIT
button to exit.
If your receiver supports audio only, it may not appear in the device list.
✎
The receiver will work when you have properly connected the optical in jack of the receiver to the
✎
DIGITAL AUDIO
OUT (OPTICAL)
jack of the TV.
When the receiver (i.e Home Theatre) is set to On, you can hear sound output from the TV’s Optical jack. When the
✎
TV is displaying a DTV (aerial) signal, the TV will send out 5.1 channel sound to the receiver. When the source is a
digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from
the receiver.
NOTE
✎
You can only control Anynet
x
+
devices using the TV remote control, not the buttons on the TV.
The TV remote control may not work under certain conditions. If this occurs, reselect the Anynet
x
+
device.
The Anynet
x
+
functions do not operate with other manufacturers’ products.
Troubleshooting for Anynet
¦
+
Problem
Possible Solution
Anynet
+
does not work.
Check if the device is an Anynet
•
+
device. The system supports Anynet
+
devices only.
Connect only one receiver (home theatre).
•
Check if the Anynet
•
+
device power cord is properly connected.
Check the Anynet
•
+
device’s Video/Audio/HDMI Cable connections.
Check whether Anynet
•
+
(HDMI-CEC) is set to On in the Anynet
+
setup menu.
Check whether the TV remote control is in TV mode.
•
Check whether it is Anynet
•
+
exclusive remote control.
Anynet
•
+
doesn’t work in certain situations. (Searching channels, operating
Media Play
or
Plug & Play
(Initial
setup), etc.)
When connecting or removing the HDMI cable, please make sure to search devices again or turn your TV off
•
and on again.
Check if the Anynet
•
+
Function of device is set on.
I want to start Anynet
+
.
Check if the Anynet
•
+
device is properly connected to the TV and check if the (HDMI-CEC) is set to On
in the Anynet
+
Setup menu.
Presshe
•
TOOLS
button to display the Anynet
+
menu and select a menu you want.
I want to exit Anynet
+
.
Select
•
View TV
in the Anynet
+
menu.
Press the
•
SOURCE
button on the TV remote control and select a device other than Anynet
+
devices.
Press
•
P
>
/
<
,
PRE-CH
, and
FAV.CH
to change the TV mode. (Note that the channel button operates only
when a tuner-embedded device is not connected.)
The message “Connecting to
Anynet
+
device...” appears on the
screen.
You cannot use the remote control when you are configuring Anynet
•
+
or switching to a view mode.
Use the remote control when the Anynet
•
+
setting or switching to view mode is complete.
The Anynet
+
device does not play.
You cannot use the play function when
•
Plug & Play
(Initial setup) is in progress.
The connected device is not
displayed.
Check whether or not the device supports Anynet
•
+
functions.
Check whether or not the HDMI Cable is properly connected.
•
Check whether
•
(HDMI-CEC)
is set to
On
in the Anynet
+
setup menu.
Search Anynet
•
+
devices again.
You can connect an Anynet
•
+
device using the HDMI Cable only. Some HDMI cables may not support Anynet
+
functions.
If it is terminated by an abnormal situation such as disconnecting the HDMI cable or power cord or a power
•
failure, please repeat the device scan.
The TV programme cannot be
recorded.
Check whether the antenna jack on the recording device is properly connected.
•
The TV sound is not output
through the receiver.
Connect the optical cable between TV and the receiver.
•
BN68-02688D_00Eng.indb 37
3/3/2010 10:31:34 PM
