background image

9

TRUE

tfm

www

.

truemfg

.

com

1

INSTALLATION INSTRUCTIONS

  

DANFOSS TEMPERATURE  CONTROL ADJUSTMENT 
FOR HIGH ALTITUDE APPLICATIONS:
REQUIRED TOOLS:

•  Allen Wrench (5/64")

•  Torx Screw (T-7)

TERMS:

Cut-out

 - Temperature sensed by the controller that shuts the 

compressor off.

Cut-in 

- Temperature sensed by the controller that turns the 

compressor on.

WHEN TO  MAKE AN ADJUSTMENT TO A  MECHANICAL TEMPERATURE  CONTROL

OPERATION INSTRUCTIONS:
REQUIRED TOOLS:

•  Jewelers Screw Driver (Small Screw Driver)

GE CONTROL INSTRUCTIONS:

The scale to the right may be used as a guide for measuring 
degrees of rotation required for altitude correction. See Figure 1.
The arrows indicate direction of screw rotation. Turn calibration 
screw clockwise to obtain warmer operating temperatures. 

NOTE:

 Each 1/4 turn of the calibration screw is equal to 

approximately 2 degrees F. Do not make more than 3/4 turn. 
After making adjustment, measure temperature during three 
cycles before adjusting again.

NOTE:

 Only adjust the screw 

(small flathead) on the face of 
the control (next to the cam). 
See Figure 3. 
Follow the Altitude Correction 
Table to the right.

WA

RMER

C OLDER

60

30

45

40

35

50

55

15

20

25

10

5

We advise to make a mechanical temperature control adjustment only for a high altitude location.

Compressor

 Terminals

Ground

Terminal

To adjust the temperature control 
take the control knob off to view the 
cut-in screw. (See Photo Above)

Front of Temperature Control

Calibration 
Screw

1

2

3

Cut-out Adjustment
Screw Allen (5/64" or 2 mm.)

Cut-in Adjustment
Screw Torx (T-7)

Compressor 
Connection

ALTITUDE  CORRECTION TABLE: 

CALIBRATION SCREW ADJUSTS 

BOTH CUT-IN AND CUT-OUT

Altitude  (Feet)

2000
3000
4000
5000
6000
7000
8000
9000

 10,000

Clockwise Turns

7/60

11/60
15/60
19/60
23/60
27/60
30/60
34/60
37/60

Compressor Connection 
(double terminal)

HOW TO ADJUST A  MECHANICAL TEMPERATURE  CONTROL

Altitude Correction

Scale Guide for Measuring

Back of Temperature Control

Bottom of Temperature Control

Summary of Contents for GALAXY Young


















Reviews: