30
31
GB
GB
Using the Feature
G-Code
Code
Code : 0 - 9
Correct :
Standard
G-Code
Timer Method
OK
OPEN/CLOSE
STANDBY/ON
7
1
Recording a Programme with Automatic Stop
This function enables you to record up to nine hours (LP) of
programmes.
Your DVD-VCR stops automatically after the requested length of
time.
1
Switch on the television.
2
To monitor the programme being recorded, select the television
channel reserved for use with your DVD-VCR (or the AV input if
used).
3
Insert the cassette on which the programme is to be recorded,
with the window visible and the safety tab intact or the opening
covered with adhesive tape.
Result:
The DVD-VCR is switched on automatically.
4
Select:
◆
The station to be recorded using the PROG ( or ) buttons
or
◆
The LINE1, LINE2 source using the INPUT SEL. button for
a satellite tuner or external video source
Result:
The channel number is displayed and the
programme can be seen on the television.
5
Select the recording speed by pressing the SPEED button as
many times as required (see page 28).
6
Hold the REC button (
●
) down for a while to start recording.
Result:
The record indicator appears on the television
screen and DVD-VCR display. An index is recorded
on the tape (see page 38).
7
Press the REC button (
●
) several times to increase the
recording time in:
◆
30-minute intervals up to four hours
◆
1-hour intervals up to nine hours
Result:
The length is displayed on the television displays.
The selected programme is recorded for the length
of time requested. At the end of that time, the DVD-
VCR stops recording automatically and power off.
8
If you wish to cancel the recording before the end, press
STANDBY/ON.
☛
If the end of the tape is reached while recording:
◆
The recording stops and power off.
☛
This function is not available in DVD recording
EJECT
AUX
3
OK
6
4
4
5
LENGTH 2:30
SET LENGTH :
PRESS
REC
●
Before presetting your DVD-VCR:
◆
Switch on both the television and your DVD-VCR
◆
Check that the date and time are correct
◆
Insert the cassette on which the programme is to be
recorded (safety tab intact)
Up to six programmes can be preset.
1
Press the TIMER button.
Result:
The
Timer Method
is displayed.
2
Press the corresponding
or
❷
buttons, until the
G-Code
option is selected.
3
Press the
❿
button to select
G-Code
.
Result:
A message is displayed to allow you to enter the
G-Code code.
☛
If all six programmes have been set, the message
Timer
is Full
is displayed. Refer to page 34 if you wish to
cancel a preset recording.
4
Press the numeric buttons to enter the code opposite the pro
gramme that you wish to record in your television magazine.
➢
If you wish to correct the G-Code code that you are
entering:
◆
Press the
➛
button until the digit to be corrected is
cleared
◆
Enter the correct digit
5
Press the OK button.
Result:
The information concerning the programme is
displayed.
☛
When using the G-Code function for the first time with
stored stations, the programme number flashes. This one
time, you must enter the station number manually by
pressing the
or
❷
buttons. Refer to the following page
if:
◆
The programme number or times flash
◆
You wish to modify the programme
6
If the programme and times are correct, press the RETURN
button.
7
Press the STANDBY/ON button to activate the timer.
8
Refer to page 34 if you wish to:
◆
Check that your VCR has been programmed correctly
◆
Cancel a preset recording
☛
The numbers next to each TV programme listing are
G-CODE code numbers, which allow you to
programme your videorecorder instantly with the
remote control. Tap in the G-CODE code for the
programme you wish to record.
™ G-CODE is a trademark of Gemstar Development Corporation. The G-CODE system is
manufactured under licence from Gemstar Development Corporation.
VCR
VCR
00316A DVD-V530A/XSA-GB2 10/14/03 4:40 PM Page 30
Summary of Contents for DVD-V530A
Page 1: ......
