background image

E-

6

Deciding on where to install the outdoor unit

Outdoor Unit

  The outdoor unit must not be placed on its side or upside down, as the  

compressor lubrication oil will run into the cooling circuit and seriously  

damage the unit.

  Choose a location that is dry and sunny, but not exposed to direct sunlight  

or strong winds.

  Do not block any passageways or thoroughfares.

  Choose a location where the noise of the air conditioner when running and 

the discharged air do not disturb any neighbours.

  Choose a position that enables the pipes and cables to be easily connected 

to the indoor unit.

  Install the outdoor unit on a flat, stable surface that can support its weight 

and does not generate any unnecessary noise and vibration. 

  Position the outdoor unit so that the air flow is directed towards the open 

area. 

  If the outdoor unit is installed at a height, ensure that its base is firmly fixed 

in position. 

  Make sure that the water dripping from the drain hose runs away correctly 

and safely.



You have just purchased a system air conditioner and it has been 
installed by your installation specialist.



This device must be installed according to the national electrical rules.



With an outdoor unit having net weight upper then 60kg, we suggest do 
not  install it suspended on wall, but considering floor standing one.

CAUTION

Summary of Contents for DC48GTTX
























Reviews: