background image

1) Turn off the the power.

Be sure to turn off the power before attempting to repair the

unit such as the disassembly of the unit.

2)  Be careful of electric shock

When checking the circuit with the power connected in

unavoidable circumstances, take special care not to touch the

live parts. There is a danger of electric shock.

3)  Use of appropriate parts

Be sure to use the genuine parts of the relevant model when

it is necessary to replace parts. (Replace parts instead of

repairing with regard to the malfunctioning of electric contact

areas. Never attempt to modify the unit. It is extremely dan-

gerous for the consumer to attempt to repair the unit on

his(her) own.)

4)  Use of proper tools

Use appropriate tools for repair, and use measuring equip-

ment after accurate calibration. Using worn tools may result

in problems, including poor contact and poor connection.

5)  Avoid damage to electric wire or electric cord.

Check the electric cord or electric wire for any damage during

repair.

Be sure to replace it if damaged.

6)  Avoid intermediate connection of the electric cord.

Never attempt to make an intermediate connection by cutting

the middle area of the electric cord or make a connection to

the power receptacle as it is very dangerous, causing prob-

lems or fire.

7)  Checking of insulation

Be sure to check the insulation resistance after completion of

the assembly work.

(Check whether the insulation resistance of the electric wire

and grounding terminal is over 30M

 by using the insulation

resistance tester, and then connect the power source.)

8)  Checking of grounding

Check the grounding condition, and perform repair if poorly

grounded.

9)  Checking of installation condition

Check the installation condition of the unit, and perform

repair if there is any defective area.

If the unit remains in an unstable installing condition, install

it at a new site.

10) Be careful of children

As the repair of the unit involves a lot of dangerous elements,

do not allow children to approach nearby during repair work.

Samsung Electronics

1-1

1. Precautions

Turn off the sub power switch separately installed.

No connection with the power receptacle

Upon completion of the repair, clean the air 
conditioner and surrounding area, and 
inform the customer of completion of the repair.

Cleaning

Summary of Contents for APH180HD




















































Reviews: