Samsung AP0AS0A Series User & Installation Manual Download Page 46

Page: 46 / 56

ENGLISH

Grounding work

Grounding must be done by a qualified installer for your safety.

Grounding the power cable

The standard of grounding may vary according to the rated voltage and installation place of the air conditioner.

Ground the power cable according to the following table.

Installation place

Power condition

High humidity

Average humidity

Low humidity

Voltage of lower than 150V

Perform the grounding work

Note 1)

Perform the grounding work 2 if

possible for your safety.

Note 2)

Voltage of higher than 150V

Must perform the grounding work 3.

Note 1)

(Including the case where

circuit breaker is installed)

Note 1)

Grounding work 3

Grounding must be done by installation specialist.

Check if the grounding resistance is lower than 100Ω. When installing a circuit breaker that can cut the electric circuit in
case of a short circuit, the allowable grounding resistance can be 30~500Ω.

Note 2)

Grounding at dry place

The grounding resistance is should be lower than 100Ω and even in worst case, it should be lower than 250Ω)

Performing the ground work

Use the grounding wire by referring to the specification of the electric cable for the outdoor unit.

❖

When using the exclusive terminal for grounding

- When exclusive terminal for grounding is installed. Ex) Steel house etc.

Exclusive terminal for

grounding

AP80S0A

Grounding resistance under

100Ω (Conventional facility)

Exclusive terminal for

grounding

AP0AS0A

Grounding resistance under

100Ω (Conventional facility)

❖

When using the exclusive terminal for grounding

Switching board

AP80S0A

Grounding resistance under

100Ω (Conventional facility)

Switching board

AP0AS0A

Grounding resistance under

100Ω (Conventional facility)

PAC_아프리카 중동향AP80S0A_IBIM_34514A-02_EN.indd 45

2015-04-23 오후 2:19:00

Summary of Contents for AP0AS0A Series

























































Search results

Summary of Contents for AP0AS0A Series

Reviews:

Related manuals for AP0AS0A Series

Brands by name

Popular brands

Samsung AP0AS0A Series, User & Installation Manual

Search results

Summary of Contents for AP0AS0A Series

Reviews:

Related manuals for AP0AS0A Series

Brands by name

Popular brands