40
Installation Procedure
English
Installation Pr
oc
edur
e
(* 1)
Duration for Auto Change Over triggered when you set dual set points in the Auto mode using the wired remote
control MWR-WG00*N.
During the automatic heating operation, if the specified time has elapsed in the state of "the room temperature >
the cooling temperature in the Auto mode + the primary cooling temperature (set in the Auto Change Over screen
after entering the User mode by pressing the button on the wired remote control)" the air conditioner changes
into the automatic cooling operation.
During the automatic cooling operation, if the specified time has elapsed in the state of "the room temperature <
the heating temperature in the Auto mode - the primary heating temperature (set in the Auto Change Over screen
after entering the User mode by pressing the button on the wired remote control)" the air conditioner changes
into the automatic heating mode.
(*2)
Height difference : The difference of the height between the corresponding indoor unit and the indoor unit
installed at the lowest place. For example, When the indoor unit is installed 131.23ft(40m) higher than the indoor
unit installed at the lowest place, select the option “1”.
(*3)
The difference between the pipe length of the indoor unit installed at farthest place from an outdoor unit and the
pipe length of the corresponding indoor unit from an outdoor unit.
For example, when the farthest pipe length is 328 ft (100 m) and the corresponding indoor unit is 131.23ft(40m)
ɇиɇц˙θͱ͔ɇ͝ͱЇϩʒͱͱθЇ̈͝ϩࡥϑʪ̷ʪʀϩϩ˵ʪͱΧϩ̈ͱ࣬͝ߤ࣭࣑ߥߤߪ˙ϩ࣑ߣߢߢ͔࣒ࣛߣߥߣߤߥ˙ϩ࣑ߦߢ͔࣒॔ߣ߫ߨߪߧ˙ϩ࣑ߨߢ͔࣒࣒
(*4)
For MTFC option, the MTFC (Multi Tenant Function Controller) accessory kit is required (purchased separately).
(*5)
Heater operation when the SEG9 of 02 series installation option is set to using hot water heater or when SEG15 is
set to using external heater.
kуɇ͔Χ̷ʪߣ࣒Ɗʪϩϩ̈͝˝ߢߤϑʪθ̈ʪϑƊk࣭߫॔ߣ࣭ࢩƊʪϩϩ̈͝˝ߢߧϑʪθ̈ʪϑƊkߣߪ॔࣬ߢ࣭ࡤƟ˵ʪ˵ͱϩиɇϩʪθ˵ʪɇϩʪθ̈ϑϩЇθ͝ʪʒͱ͝ɇϩϩ˵ʪ
same time as the heating thermostat is on, and turned off when the heating thermostat is off.
kуɇ͔Χ̷ʪߤ࣒Ɗʪϩϩ̈͝˝ߢߤϑʪθ̈ʪϑƊkߣߧ࣭॔ߤ࣭ࢩƊʪϩϩ̈͝˝ߢߧϑʪθ̈ʪϑƊkߣߪ࣭࣭॔ࡤŵͱͱ͔ϩʪ͔Χख़ϑʪϩϩʪ͔Χॐ˙࣑˵ʪɇϩ̈͝˝
compensation temp.)
–
kуϩʪθ͝ɇ̷˵ʪɇϩʪθ̈ϑϩЇθ͝ʪʒͱ͝и˵ʪ͝ϩ˵ʪϩʪ͔ΧʪθɇϩЇθʪ̈ϑ͔ɇ̈͝ϩɇ̈͝ʪʒɇϑߪߣছ࣑ߦߧঙ࣒˙ͱθߣߢ͔̈͝Їϩʪϑŵͱͱ͔ϩʪ͔Χॖ
set temp. + f(heating compensation temp.)
–
kуϩʪθ͝ɇ̷˵ʪɇϩʪθ̈ϑϩЇθ͝ʪʒͱ˙˙и˵ʪ͝ϩ˵ʪϩʪ͔ΧʪθɇϩЇθʪ̈ϑ͔ɇ̈͝ϩɇ̈͝ʪʒɇϑߪߣছ࣑ߦߧঙ࣒ॐߣߪছ࣑ߣঙ࣒࣑ߣߪছ࣑ߣঙ࣒̈ϑϩ˵ʪ
Hysteresis for On/Off selection.)
ki]_TXXXW^hTWXptk}tG~GmGX hhluUGGG[W
YWYXTXWTYWGGG㝘㤸GXXa[_a\]
Summary of Contents for AM AN1PCH Series
Page 48: ......
