background image

9

Stage 412: Quad Handheld Wireless System

1.  Status Indicator - This LED displays the 

operation mode: 
 

GREEN

Normal Operation

RED

Mute

Flashing GREEN

Low Battery

2.  Power/Mute Switch - Press and hold to turn the 

unit on or off. Press and release to mute or 
unmute the transmitter. 

3.  Battery Cover - Unscrew the battery cover 

and slide down to open the VH12 battery 
compartment.

4.  Battery Holder - Open the battery holder by 

pressing the tab and lifting the cover. Insert 
two standard AA (LR6) batteries here, being 
sure to observe the plus and minus polarity 
markings shown.  
WARNING: Do not insert the batteries 
backwards; doing so can cause severe damage 
to the VH12 and will void your warranty.

5.  Input GAIN Control - This control adjusts the 

transmitter input sensitivity. For optimal 
performance, using the included screwdriver, 
set the input GAIN control to where you see 
the VH12 PEAK indicator start to light under 
high levels, then turn down until the PEAK 
light stops lighting. 

6.  IR Lens - This window is used to capture the 

infrared signal sent from the VH12 during 
the IR SET to channelize the transmitter. The 
battery cover must be open and the IR Lens 
facing towards the receiver to load the selected 
channel. 

7.  Plastic Screwdriver - Designed for use in 

adjusting the VH12 input GAIN control (See 
#5 

Input GAIN Control).

VH12 Transmitter Controls and Features

Summary of Contents for STAGE 412

















Reviews: