background image

13

Stage 412: Quad Handheld Wireless System

Specifications

System Specifications
Operating Frequency 

VHF 173 MHz to 198 MHz

Number of Frequencies per Channel  

6

Frequency Stability 

±0.005%

Modulation Mode 

FM

Maximum Deviation 

±30 kHz

Operating Range 

200’ / 60m

Operating Temperature Range 

40° to 43°

Working Humidity 

65±20%RH

Frequency Response 

80 Hz to 15 kHz

Tone Key Frequency 

30.00 kHz

 
SR412 Receiver Specifications:
Image Rejection 

35 dB

Dynamic Range 

100 dB

Maximum Output 

1.37 V

Sensitivity 

-100 dBm @ 30 dB SINAD

Output Connectors 

Two 1/4” (6.3 mm) unbalanced, Three XLR balanced

Audio Output Levels 

-12dB

Power Supply 

100-240V, 50/60Hz, 0.4A, Output: DC 15V, 800mA 

Dimensions 

 16.92” x 6.7” x 1.57” / 430 mm x 170 mm x 40 mm

Net Weight 

3.08 lb / 1.4 kg

 

VH12 Transmitter Specifications
RF Power Output 

10mW

Microphone Element 

Q6 Dynamic 

Typical Battery Life 

12 hours

Current Consumption 

120 mA typical

Dimensions 

 ø2.16” x 10” / ø55 mm x 255 mm

Net Weight 

0.48 lb / 0.22 kg

At Samson, we are continually improving our products, therefore specifications and 

images are subject to change without notice.

Summary of Contents for STAGE 412

















Reviews: