background image

1

Introduction

Welcome to Samson AirLine Synth—the next generation of wireless systems! Wireless 

microphone and instrument systems were originally developed to eliminate cables, 

providing unparalleled freedom of movement. AirLine Synth takes this concept 

to a new level with transmitters so small, lightweight and aerodynamic, they are 

nearly invisible, providing a completely “hassle-free” user experience. To create the 

world’s smallest frequency agile wireless transmitters, we developed new proprietary 

technology. Featuring miniaturized circuitry and the ability to operate on a single AA 

battery (with 10 hours typical battery life), these transmitters also provide significantly 

improved wireless reception and sound quality. What’s more, the AR300 receiver 

developed especially for the AirLine Synth guitar system provides an automatic 

Channel Scan function to help you find the clearest frequency to operate on. Once 

the AR300 finds the clearest channel, it’s easy to set the AG300 transmitter to the 

matching channel using the IR SET feature. The convenient, all metal half-rack chassis 

design features a large backlit LCD display and includes a rackmount kit to install into 

a standard 19-inch equipment rack. The Samson AirLine Synth UHF guitar system is 

designed to replace the cable between your electric guitar or bass and your onstage 

amplifier or PA mixer, freeing you to roam the stage or even visit the audience in the 

middle of your performance!  It operates in the UHF frequency range and contains an 

AR300 “half-rack” receiver and the AG300 plug-in micro-transmitter designed to fit the 

recessed style jack in Fender Stratocaster™-type guitars, or convertible, to fit all other 

standard end-mount guitar jacks.

In this manual, you’ll find a detailed description of the features of your AirLine Synth 

system, as well as a guided tour through all components, step-by-step instructions for 

setting up and using your system and full specifications. If your AirLine Synth system 

was purchased in the United States, you’ll also find a warranty card enclosed—don’t 

forget to fill it out and mail it! This will enable you to receive online technical support 

and will allow us to send you updated information about this and other Samson 

products in the future. If your AirLine Synth system was purchased outside of the 

U. S., contact your local distributor for warranty details. Also, be sure to check out 

our website (http://www.samsontech.com) for complete information about our full 

product line.

SPECIAL NOTE for U.S. purchasers: Should your AirLine Synth system ever require 

servicing, a Return Authorization number (RA) is necessary. Without this number, 

the unit will not be accepted. If your AirLine Synth system was purchased in the United 

States, please call Samson at 1-800-372-6766 for a Return Authorization number prior 

to shipping your system. If possible, return the unit in its original carton and packing 

materials. If your AirLine Synth system was purchased outside of the U. S., contact your 

local distributor for information.

Summary of Contents for AirLne SYNTH

























Reviews: