background image

WARNING

TO PREVENT FIRE OR SHOCK HAZARD. DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE 

OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

TO PREVENT FIRE OR SHOCK HAZARD. DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

TO PREVENT ELECTRICAL SHOCK, MATCH WIDE BLADE PLUG TO WIDE SLOT AND FULLY INSERT.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

This lightning flash with 

arrowhead symbol, within an 

equilateral triangle, is 

intended to alert the user to 

the presence of uninsulated 

“dangerous voltage” within 

the product’s enclosure that 

may be of sufficient magni-

tude to constitute a risk of 

electric shock to persons.

Warning: To reduce the risk of 

electric shock, do not remove 

cover (or back). No user-

serviceable parts inside. For 

service, refer to qualified 

service personnel.

The exclamation point within 

an equilateral triangle is 

intended to alert the user to 

the presence of important 

operating and maintenance 

(servicing) instructions in the 

literature accompanying the 

appliance.

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus 

(including amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two 

blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. 

The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your 

outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at the plugs, convenience recep-

tacles, and at the point where they exit from the apparatus.

Only use attachments/accessories specified by the manufacturer.

Use only with the cart, stand, tripod, bracket, or table specified by the manu-

facturer, or sold with the apparatus. When a cart is used, use caution when 

moving the cart/apparatus combination to avoid injury from tip-over.

Unplug the apparatus during lightening, sort or when unused for long periods of time.

Refer all servicing to qualified personnel. Service is required when the apparatus has been damaged in 

any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen 

into the apparatus has been exposed to rain or moisture, does not operate normally, or has been 

dropped.

This appliance shall not be exposed to dripping or splashing water and that no object filled with liquid 

such as vases shall be placed on the apparatus.

Caution-to prevent electrical shock, match wide blade plug wide slot fully insert.

Please keep a good ventilation environment around the entire unit.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

IMPORTANT SAFETY INSTRUCTIONS

Summary of Contents for AirLne SYNTH

























Reviews: