HOW TO CLEAN SILICONE WIPERS
The silicone wipers are removable for cleaning. After cleaning, place the
silicone wipers back onto the frame as shown in the picture below.
TROUBLESHOOTING
Problem
Solution
No power to the juicer
• Check if the power cord is properly plugged in.
• Check if the drum lid and the juicing bowl are
in place.
• Check if the top-set and the base are properly
assembled.
•
Juicer will not operate if the parts are not
assembled properly.
Low juice yield
• The juice yield depends on the water content
of the ingredients.
• If the ingredients are not fresh, they contain
reduced amount of fluids.
• Check if the compression silicone is firmly
inserted.
• If the ingredient itself has low water content, it
may help to soak it in water before juicing.
• If juicing ingredients with small seeds, after
a few servings it may reduce the juice yield.
Disassemble and wash the top-set in between
juicing.
• If there is seed residue on the bottom of the
strainer it can affect juicer performance and
the overall juice yield.
There is too much pulp
in the juice
• When continuously juicing, depending on the
ingredient the juice may contain a lot of fine pulp.
• To reduce the fine pulp, clean the top-set fre
-
quently and extract the pulp.
• Use the mesh strainer and put the juice throu
-
gh it to collect the unwanted pulp.
• If the strainer and the screw are damaged, it is
recommended to replace the parts.
• The lifetime of each part may vary depen-
ding on length and method of use and ingre-
dients extracted.
• If too many ingredients are inserted at the
same time, it may cause juicer to stop frequent
-
ly. This can lead to pulpy juice. Insert ingredients
slowly and few at a time.
The drum lid will not
close
• Make sure the juicing screw is pushed all the
way in to the strainer in order for the drum lid to
close properly.
• If the juicing screw is not properly in posi-
tion, the drum lid may not close.
Odd noise from the
juicer
• Check if the parts are assembled correctly.
• Try reassembling the parts and listen for the
odd noise.
• Do not start the juicer unless there are ingre
-
dients and/ or liquid in it.
• Operating the juicer without ingredients can
cause damage to the screw and increase the
noise level.
• The friction noise from the juicing screw and
the strainer will disappear when ingredients are
inserted into the juicer.
• If noise occurs when the ingredients are inser-
ted into the juicer, check the size of ingredients.
Do not insert anything over 2.5cm of thickness.
• Depending on the type of ingredients, the
dimensions can be smaller.
• The noise can occur if the juicer is opera-
ted on an uneven or slanted surface. Place
the juicer of a horizontally flat surface while
operating.
The extracted pulp is
very moist
• During the very beginning of extraction the pulp
can be more moist.
• Depending on the ingredient’s condition, the
extracted pulp can be affected; especially when
the ingredient is not fresh, the juice can be
extracted with the pulp.
During operation the
juicing bowl shakes
• The juicing screw and the strainer are set up to
crush and squeeze the ingredients. It is normal
for the juicing screw and the strainer to vibrate.
• If the ingredient contains strong fiber, the vibra
-
tion from the top-set may be stronger.
During juicing the jui
-
cer stopped
• Check the power cord and make sure it is
plugged in correctly.
• Check that all the parts are correctly assem-
bled.
• If too many ingredients are inserted at once,
this can cause the juicer to stop.
• When the juicer stops because there are too
many ingredients in it, press the REVERSE
– OFF – FORWARD buttons in this order, swit-
ching back and forth 2 – 3 times.
• The reverse setting will push the ingre-
dients up and the forward setting will pull the
ingredients down.
If the juicer stops due to the overload protection,
let the juicer cool down for 30 minutes to 2 hours
before juicing again.
If there are hard seeds within the ingredients,
remove them before juicing. Hard seeds can
damage the juicer.
Layers of separation in
the juice
• Depending on the density of the ingredients,
the extracted juice may show layers of different
juices. It is different from separation due to
oxidation caused by juicing with a high-speed
juicer.
14
EN
