background image

5

1. INTRODUCTION

Thank you for purchasing a Samlex Europe (Samlex) Elogic DC to DC battery charger.  
Please read this owner’s manual for information about using the product correctly and safely. 
Keep this owner’s manual and all other included documentation close to the product for  
future reference. For the most recent manual revision, please check the downloads section  
on our website.
 
The purpose of this owner’s manual is to provide explanations and procedures for installing, 
configuring and operating the battery charger. The installation instructions are intended 
for installers that should have knowledge and experience in installing electrical equipment, 
knowledge of the applicable installation codes, and awareness of the hazards involved in 
performing electrical work and how to reduce those hazards.

1.1 

Intended product use

The Elogic DC to DC battery chargers are primarily intended to charge an auxiliary or service 
battery from a vehicle starter battery. The input battery voltage can be above, below or  
equal to the output battery voltage. An Elogic DC charger allows the auxiliary battery to be 
perfectly charged regardless of the input voltage, while being protected against damage due  
to peak voltages.

The Elogic DC battery chargers are compatible with vehicles that are equipped with variable 
output smart alternators (EUR 6+). The Elogic DC charger can start charging based on a 
programmable input voltage range only, or in combination with an engine run signal. There is 
also a separate (BMS-) control input available that enables external control for charger-on  
and -standby. 

1.2 

Important safety information 

This section contains important safety information for the Elogic DC battery charger. Each time, 
before using the Elogic DC battery charger, READ ALL instructions and cautionary markings on 
or provided with the battery charger, and all appropriate sections of this guide.  
This battery charger contains no user serviceable parts. Opening up the battery charger will 
void product warranty.
 

WARNING

FIRE AND/OR CHEMICAL BURN HAZARD
Do not cover or obstruct any air vent openings and/or install in a zero clearance compartment.

WARNING

SHOCK HAZARD. KEEP AWAY FROM CHILDREN!
Avoid moisture ingress. Never expose the unit to snow, water, etc.

 

Summary of Contents for ELOGIC























Reviews: