SAMES KREMLIN REXSON SH0910 User Manual Download

Page: 41 / 50

Disassembly / Reassembly Operation

Disassembly of the pump



Unscrew the nuts (19) and put aside the flange (1), the tie
rods (14) and the protection (4),



Clamp the pump horizontally through the body (7) with a
vice,



Unscrew the nut (35) and take off the shovel (34), the
washer (33) and the spacer (32),



Unscrew the tube (37) and take off the seal (36),



Unscrew the valve body (21) and the outlet with the lower
valve (28) and its seat (30),



Remove the piston / shovel rod assembly,



Unscrew the cylinder (10).

Cup seals

Nota: the pump body (7) consists of a cartridge (7b) to make
easier the changing of the seals.



Unscrew the cup (5),



Take off the 12 screws (7d) that tighten the cartridge (7b) in
the body (7a),



Take off the cartridge (7b) screwing the extractors in the 3
M8 holes of the cartridge,



Take off the washers (6 & 12) and the seals (11),



Change the seals (11),



Change the seal (7c).



Clean and reinstall the parts in the reverse order of the
disassembly sequence.

S 1

Summary of Contents for REXSON SH0910



















































Search results

Summary of Contents for REXSON SH0910

Reviews:

Related manuals for REXSON SH0910

Brands by name

Popular brands

SAMES KREMLIN REXSON SH0910, User Manual

Search results

Summary of Contents for REXSON SH0910

Reviews:

Related manuals for REXSON SH0910

Brands by name

Popular brands