SAMES KREMLIN REXSON 2B227 Page 51 User Manual Download

Page: 51 / 54

Spare parts

Lower adapter flange

Ind.

Description

# Ref.

Qty

Spare part

maintenance

level**

Lower adapter flange for motors 6000, 7000 and 9000

144 245 493



Connecting flange assembly

N.S. (044 245 197)

**1



Connecting flange

N.S. (210 620)

**2



Screw CHc M18x55

N.S. (88 960)

**13



N.S. (209 582)

**4



Protective housing

N.S. (044 230 010)

**14



Tie-rod

N.S. (209 621)

* Recommended maintenance parts.

N S: Denotes parts are not serviceable.

**Level 1 : Preventive maintenance

Level 2 : Corrective

maintenance

Level 3 : Exceptional

maintenance

Recommended Seals pack

Code

Composition

Use

PTFE (+ FKM)

Solvent - Ether - Ketone - Aromatic alcohol - some varnishes and paints

PTFE (+ FKM / FEP)

Solvent - Ether - Ketone - Aromatic alcohol - some varnishes and paints, PU
paints - Pharmacy - Cosmetics - Some foodstuffs

PTFE + PE (+ FKM)

Epoxy glue - Butyl - Silicone - Some varnishes - Paint

PE + LEATHER (+ FKM)

Paint - Varnishes - Grease - Oil - Ink - Hydro soluble paint

GRAPHITED PTFE (+ FKM)

Paints - Varnishes - Inks - PVC compounds - Butyl

PU + GRAPHITED PTFE (+ FKM) Mastics - PVC - Butyl

GRAPHITED PTFE /PE (+ FKM)

Paint - Varnishes - Grease - Oil - Inks - Hydro soluble paint - Mastics - PVC -
Butyl

GRAPHITED PTFE + PTFE

Zinc special

Accessory

Ind.

Description

# Ref.

Qty

Bottle of lubricant T (125 ml / 0,034 oz)

149 990 020

Summary of Contents for REXSON 2B227























































Search results

Summary of Contents for REXSON 2B227

Reviews:

Related manuals for REXSON 2B227

Brands by name

Popular brands

SAMES KREMLIN REXSON 2B227, User Manual

Search results

Summary of Contents for REXSON 2B227

Reviews:

Related manuals for REXSON 2B227

Brands by name

Popular brands