background image

 
 

Operator’s manual 

Rear disc mowers 

with central suspension 

KDTC 260 S/W; KDTC 300 S/W; KDTC 340 

 

- 8 - 

 

4.

 

SAFETY ADVICE 

 

4.1.  Safety rules and regulations 

 

Front  axis  of  the  tractor  should  be  weighted  to  keep  the  balance.  If  need  be,  use  front  wheel 
weights. 

 

Any  operation  with  the  hydraulic  lift  lever  should  be  done  from  the  operator’s  seat;  DO  NOT 
move the lever from outside of the tractor. 

In  case  of  tractors  equipped  with  EHR,  operating  with  hydraulic  lift  is  done  by  the  buttons 
mounted outside the tractor’s cabin. When operating be extremely careful. 

 

When switching  from working to transport position unmount the whole or at least one end (from 
tractor’s PTO) of PTO shaft. 

 

Operation  without  safety  guards  as  well  as  with  the  damaged  or  raised  guards  is  not  allowed 
(danger of the stones, etc. being thrown out). 

 

Start mowing only when the tractor’s PTO reaches its normal 1000 rpm. 

 

DO NOT exceed 1050 PTO rpm, 

 

Nobody  is  allowed  to  remain  within  the  danger  area  of  at  least  50  m.  Particular  caution  is 
necessary when operating near roads and in stoney areas, 

 

Any maintenance and adjustment work should only be done after the drive has been disconnected 
and when the cutting discs have come to the complete standstill, 

 

Always  check  the  mower  before  starting  work,  in  particular  for  damaged,  missing  and/or  worn 
knives and knife holders. Damaged or worn parts must be replaced. 

 

When driving on public roads always comply with  local traffic regulations, especially concerning 
warning lights. 

 

CAUTION: 
All  service  and  repair  operations  must  be  done  only  after  the  tractor 
engine  has  been  stopped,  all  rotating  parts  have  come  to  the  complete 
standstill and the cutterbar is on the ground. 
 
CAUTION: 
Be certain that children and animals are at a safe distance away from the 
machine. Never allow anyone to ride on a machine or tractor. 
 

 

 

When  the  mower  is  lifted  for  repair  on  the  3-point  linkage,  it  should  be  secured  against  
falling by a mechanical support or by chain. 

 

The  bolts  and  other  fasteners  have  to  be  periodically  checked  and,  if  necessary,  tightened  or 
replaced. DO NOT work with damaged or worn fasteners. 

 

Never lift the mower on tractor linkage when the drive is on and the cutting discs are rotating. 

 

When operating the mower, the tractor should always be equipped with the cabin. 

 

Mower should not be operated when the tractor-mower set is not balanced. 

 

Never start the mower when it is lifted. 

 

Never start the mower, when people or animals are near the machine. 

 

Never lift the safety guard before the rotating parts have come to the complete standstill. Tractor’s 
engine must be stopped. 

 

Always comply with safety decals describing hazards, and warning signs placed on the machine. 

 

Before you start the tractor make sure that every other drives are turned off and the levers steering 
hydraulics are in neutral position. 

 

Never leave the tractor’s engine running without supervision. Before you leave the tractor, turn off 
the engine and put off the key from tractor’s ignition switch, 

 

It is forbidden to operate the mower when driving backwards, 

 

Never get on the mower, 

Summary of Contents for KDTC 260






































Reviews: