manualshive.com logo in svg

Salus ST101ZB, Quick Start Manual

Share
Download
Salus ST101ZB Quick Start Manual Download Page 2

Notices 

Please  read  these  instructions  carefully 

before  installing  and  using

  the  Low 

Voltage Fan Coil Thermostat. 

•

 

Follow all local and electricity supplier regulations regarding the installation or 
replacement of a thermostat. An authorized, qualified installer may be required. 

•

 

Do  not  connect  any  of  the  terminals  to  a  120/240  VAC  supply

.  The  Low 

Voltage Fan Coil Thermostat uses a 24 VAC power source. 

•

 

Do not

 cover any of the vents on the thermostat. 

•

 

Do not

 place the unit in a bathroom or area of excessive moisture. 

•

 

Do not

 allow the unit to get wet. This device serves as a temperature control 

system only in dry, closed living and office spaces. 

•

 

Do  not

  use  solvents  or  aggressive  cleaning  agents.  A  dry,  soft  cloth  is 

recommended.

 

The manufacturer does not accept responsibility for any damage caused by not 
following these instructions. 

Summary of Contents for ST101ZB

















Reviews:

No comments

Brands by name

Popular brands

Load more brands