background image

RESET

5

Select increment. Press 

Installer Mode

Press and hold     and      and     keys to enter installation setting.
The first setting is temperature display resolution selection - d01. Press     to enter the existing setting. The 
setting will start flashing. Press     or     to change temperature display  resolution, wait for 10 seconds to 
confirm, then enter d02 (if you didn’t  press     to save your selection, the change will be confirmed after 10 
seconds and the thermostat will return to normal mode). d02 is to set temperature offset, press      or      to 
increase/decrease offset. 
To exit Installer Mode don’t press any key for 10 seconds, or press 
See the table below.

RESET

Press the three buttons 

together for 3 seconds.

3 Sec

3 Sec

3 Sec

dxx

Function

Parameter

Description

Default

value

d01

Temperature display 
increments

0.1°C or 
0.5°C

Select the temperature display 
increments 

0.5°C

d02

Temperature offset

+/-3.0°C

Calibrate your thermostat tempera-
ture

0.0°C

d03

Frost setpoint temperature

5.0°C-17.0°C

Set the Frost Point temperature

5.0°C

Enter first d01 setting. Press 

2

Continue adjusting the d02 and d03 following the same steps as above. 
Once you have finished setting up all the parameters, press          to exit 
to home screen, or don’t press any button for 10 seconds and it will 
exit automatically

TESTING/PAIRING

TESTING/PAIRING

08   RT310 Installation Manual

Summary of Contents for RT310















Reviews: