background image

Tel:  886.2.2175 2930 Email: [email protected] 

www.salukitec.com

 

11 

 

 

Bad grounding or failure of the power supply may cause damage to the instrument, even 
personal injury. Before connecting the power supply of signal generator, make sure ground 
wires of the instrument and its power supply are in good contact. 
Use a power socket with protective grounding and do not substitute the protective ground 
wire with an external cable. 

3.1.4

 

Electrostatic Protection 

ESD can damage or destroy electronic components and equipment. Antistatic measures are usually taken to prevent ESD 
damage: conductive table–mat and wrist–strap combination as well as conductive floor–mat and heel–strap combination. Both 
types, when used together, provide a significant level of ESD protection. Among the two, only the table–mat and wrist–strap 
combination provides adequate ESD protection when used alone. To ensure user safety, the static–safe accessories must 
provide at least 1 MΩ resistance to ground. 
Please use the following antistatic measures correctly to reduce the damage of electrostatics: 
Ensure all the instruments are grounded correctly to prevent the electrostatics being generated. 
Before touch the joint and core wire or do any assembly operation, do wear antistatic wrists or take other antistatic measures. 

 

The above antistatic measures shall not be taken where the voltage is larger than 500V. 

3.1.5

 

First Power Up 

1)

 

Connect the provided power cord instrument end to the power socket on rear panel.   

2)

 

Ensure the AC power is compliant to requirement. 

3)

 

Check the power switch on rear panel and ensure it is off (“O”) 

4)

 

Connect the other end to AC power 

5)

 

Turn on the switch on rear panel (“|”) 

6)

 

Press the power button on front panel. 

7)

 

Screen lighted and the instrument is on. 

8)

 

For an accurate measurement, please warm up the signal generator for at least 30min before measurement. 

Summary of Contents for S1131
































Reviews: