background image

 

 
 

1. 

IMPORTANT SAFEGUARDS 

 

CAUTION 

PLEASE READ CAREFULLY THE FOLLOWING SAFETY GUIDELINES BEFORE 
OPERATIONING THIS APPLIANCE. 
 

 

Do not use the patio heater for indoors, as it may cause personal injury or 
property damage. 

 

This outdoor heater is not intended to be installed onto recreational vehicles 
and/or boats. 

 

Installation and repair should be done by a qualified service person. 

 

Improper installation, adjustment, alteration can cause personal injury or 
property damage. 

 

Do not attempt to alter the unit in any manner. 

 

Never replace or substitute the regulator with any regulator other than the 
factory-suggested replacement. 

 

Do not store or use petrol or other flammable vapors or liquids in the heater 
unit. 

 

The whole gas system, hose, regulator, pilot or burner should be inspected for 
leaks or damage before use, and at least annually by a qualified service person. 

 

All leak tests should be done with a soap solution. Never use an open flame to 
check for leaks. 

 

Do not use the heater until all connections have been leak tested. 

 

Turn off the gas valve immediately if smell of gas is detected. 

 

Do not transport heater while it is in operation. 

 

Do not move the heater, after it has been turned off, until the temperature has 
cooled down. 

 

Keep the ventilation opening of the cylinder enclosure free and clear of debris. 

 

Do not paint the radiant screen, control panel or top canopy reflector. 

 

Control compartment, burner and circulation air passageways of the heater 
must be kept clean. 

 

Frequent cleaning may be required as necessary. 

 

The LPG cylinder should be turned off when the heater is not in use. 

 

Check the heater immediately if any of the following occurs: 

-

 

The heater does not reach its set temperature. 

-

 

The burner makes a popping noise during use (a slight noise is normal 
when the burner is extinguished). 

-

 

The smell of gas in conjunction with extreme yellow tipping of the burner 
flames. 

 

The LPG regulator/hose assembly must be located out of pathways where people 
may trip over it or in an area where the hose will not be subject to accidental 
damage. 

 

Any guard or other protective device removed for servicing the heater must be 
replaced before operating the heater. 

 

Adults and children should stay away from high temperature surfaces to avoid 
burns or clothing ignition. 

 

Children should be carefully supervised when they are in the area of the heater. 

 

Clothing or other flammable materials should not be hung on the heater or 
placed on or near the heater. 

 
 
 

Summary of Contents for SOD 12
















Reviews: