Salora ELITE 1 Instruction Manual Download

Page: 6 / 29

GENERAL FUNCTIONS

Setting the equaliser
The USER sound setting allows you to make your own personal equaliser settings.
1. Repeatedly press the

DSC/UBS button

to select the USER sound setting.

2. Press and hold the

DSC/UBS button

until “BASS 0” is shown on the display.

3. Briefly Press the

DSC/UBS button

to choose the setting between BASS or TREBLE (TRE).

4. Set the value by using the

Volume buttons

Notes:
If you do not press any button within 5 seconds, the device will quit the setting.

Listening with headphones
1. Connect the headphones to the headphone jack (Ø3.5mm).

–This switches off the loudspeakers.

Warning:
Excessive sound pressure from earphones and headphones can cause hearing loss.

TIME SETTING

A demo programme starts when you use the device for the first time. The time and day will flash on the
display, indicating that they need to be set.

Time setting may only be performed in standby mode.

1. Press the

Time button

to select the hour format between 12HR and 24HR.

2. Press and hold down the

Time button

until the hour digits flash on the display.

3. Set the hour by using the

Rewind or Forward button

, and press the

Time button

to confirm.

The minute digits flash.

4. Use the

Rewind

Forward button

to set the minute, and then press the

Time button

to confirm.

The day of week flashes.

5. Set the day of week by using the

Rewind

Forward button

, and press the

Time button

to confirm.

“CT ON” flashes on the display.

6. Use the

Rewind

Forward button

to set the RDS time synchronisation, press the

Time button

confirm and finish the time setting.

Notes:
You must reset the time after a power failure or when the mains plug is pulled out.

Some RDS stations transmit an RDS time signal. If the selected RDS programme transmits this time
information, the time will be automatically updated. This may take a few minutes.

TUNER MODE

Connecting the antenna
1. Plug the outdoor antenna cable or the wire antenna supplied into the

FM Antenna socket

Fully extend the wire antenna for FM reception.

2. Insert the MW frame antenna supplied into the

MW Antenna connector

Adjust the position of the antenna to have better reception.

Selecting the Tuner input source
1. Switch on the device by pressing the

On/Off button

2. Press the

Function button

to select the input source, FM Tuner or MW Tuner.

Automatic station search
The first time you switch on the device, the automatic station search in tuner mode searches and stores
up to 40 stations (20 stations each for FM and MW) with the best reception.

1. Switch on the device by pressing the

On/Off button

. The search starts.

After the search has finished, you will hear the station stored in preset position P01.

2. To find other stations, press the

Function button

to select the frequency band, FM or MW.

3. Press and hold the

Rewind

Forward button

until the frequency display changes to rapid

run-through. The search will stop automatically when it finds a station with sufficient strength.

4. When the end of the frequency band is reached, it will recommence searching from the opposite

end of the frequency band.

Notes:
The automatic station search can be interrupted by briefly pressing the

Stop button

Manual station search
1. To move the frequency in step, briefly press the

Rewind

Forward button

The frequency changes in steps of 50kHz (FM) or 9kHz (MW).

2. When the end of the frequency band is reached, it will recommence searching from the opposite

end of the frequency band.

Storing stations as presets
1. Press the

Rewind

Forward button

to select the station desired to store.

2. Press the

Program/Random button

to activate the storing function. The preset position (e.g. P01)

and “

PROG” flash on the display.

3. Choose the desired preset position by using the

Down button

4. Press the

Program/Random button

to store the station.

5. To store more stations, repeat step 1 to 4.

Notes:
If stations are already stored in the preset positions, they are overwritten when new stations are stored.
If the device is disconnected from the mains for a period of time, all the preset stations are deleted.