Sailor H2192, Technical Manual, Page: 8 / 20

2 INSTALLATION H2192
2.2 MECHANICAL ASSEMBLING
ASSEMBLY INSTRUCTION
The respective letters A-B-C-D-E-F-G-H-K-L-M refers to the assembly drawings and to the set of screws
enclosed.
A: Screws M4 x 10mm and M4 lock washer are mounted in the mounting profiles (marked 1) as shown.
B: The mounting profiles (marked 1) are fastened to the base mounting plates (marked 2 & 3).
C: Tabletop mounting: Drill the ø8mm holes in the table, using the enclosed drilling template, at least
2 holes in each profile must be used, the * marked hole must always be used. Please refer to the
drilling plan for table mounting. Next step is to place the previous assembled hardware (B) on the
table and fasten it with the enclosed bolts and washers as shown.
Bulkhead mounting: If the console is mounted on bulkhead it must be fastened on the bulkhead
with M8 bolts in the appropriate holes in the base mounting plates. Please refer to the drilling plan
for bulkhead mounting.
D: The black cable bearers (marked 5) and the ground cables for the single units are mounted on the
base mounting plates with M4 x 6mm screws (long) as shown. Note that the screw without ground
cable must be M4 x 5mm screw (short).
E: The center Connection Board (module 1, marked 6), the left Connection board (module 2, marked
7) and Power Supply N420 (marked 8) are mounted on the base mounting plates as shown. The
3 receiver protecting units H1223 (marked 9) are mounted in right section, if it is a 2 sections
console the receiver protecting units must be placed on the bulkhead or in an other appropriate
position.
F: The mounting angles for PS/AF chassis (marked 10 and 11) are mounted on the base mounting
profiles as shown. Next step is to mount the PS/AF chassis (marked 12).
G: The earth strip is connected and fastened by the dog (marked 13).
H: The lower mounting plate (marked 14) and upper mounting plate (marked 15) are mounted as
shown.
K: The left cover plate (marked 16), the right cover plate (marked 17) and top cover plates (1/1 top
cover plate marked 18) and (1/2 top cover plate marked 19) are mounted as shown.
L: Mounting of all units in the GMDSS Station and mounting of cables as shown in the cable plan.
The following premounting are necessary on all units before they can be mounted in the console.
Mount the mounting angles (SP Number 227641, stainless steel) on all 1/4 boxes, use the screws
M5 x 7mm (marked 1, SP Number 87.284).
Mount the mounting angles (227641 and 227642 in stainless steel) on the Inmarsat-C Transceiver
and the 2 Message terminals, please note that the 5 holes in the mounting angles must be pointing
to the front of the units. Next step are to mount the cover plates with the appropiate streamers above
the units. Use the screws M4 x 5mm (marked 2, SP Number 87.160).
If you wish to mount units on top of the console, please refer to drawing 2/3. At first you must remove
the cover plates (marked 18/19), next step are to mount the 2 angles (SP Number 227654) for each
unit, use the screws M4 x 5mm (marked 2, SP Number 87.160). Remember to mount the 2 stop
screws M3 x 6mm (marked 3, SP Number 86.962) for each unit.
Mount all units in the console.
M: Mount the top cover plates (marked 20), cover plates (marked 21) and rear cover plates (marked
22). Mount the Center Panel (marked 23) and frontpanels (marked 24). Next step are to mount the
frontpanels (marked 25 & 26).
PAGE 2-3