Copyright Safewaze 2023
Page 15
The working life of Safewaze SRLs are determined by work conditions, care, maintenance, and proper inspections. As long as the SRL passes inspection, it may
remain in service.
19.3 PRODUCT LIFE
FIGURE 11 - LABELING
20.0 LABELING
Dispose of the Safewaze SRL if it has been damaged by fall arrest forces or inspection reveals an unsafe or defective condition that cannot be repaired by an
authorized Safewaze Service Center. Before disposing of the SRL, cut the lifeline in half so that it is not mistakenly reused. For questions regarding disposal,
service, or repair of Safewaze SRLs, contact Safewaze at (800) 230-0319.
19.4 DISPOSAL
1
Class
Anchor at or above
the dorsal D-ring
470-00029
020051
ANSI Z359.14 - 2021
OSHA 1910.140, OSHA 1910.66
ASTM F887
470-00031
SPECIFICATIONS:
Materials: Steel hardware, Clear resin housing, Nomex® label cover, and Kevlar® webbing
Working length: 7 ft. (2.13 m)
Capacity: ANSI 130-310 lbs. (58.97-140.61 kg), OSHA up to 420 lbs. (190.51 kg)
*including clothing, tools, & equipment
Standards: ANSI Z359.14-2021, OSHA 1910.140 and 1910.66, ASTM F887
MODEL# 020-5200
DESCRIPTION: Latitude Pro Arc Flash 7' Single Web SRL: Carabiner, Snap Hook
SERIAL #: XXXXXXX MFG DATE: XX/XXXX
MUST FOLLOW ALL MANUFACTURER’S INSTRUCTIONS INCLUDED WITH THIS EQUIPMENT. DO NOT REMOVE LABEL.
644216349531
225 Wilshire Ave SW
Concord, NC 28025
USA
(800) 230-0319
www.safewaze.com
CLASS 1 UNIT
(Anchor at or above dorsal d-ring)
A
bo
ve
D
-r
in
g
U
se
Standard
ANSI Z359.14-2021
(Class 1)
B
el
ow
D
-r
in
g
U
se
Standard
OSHA 1910.140 &
OSHA 1910.66
Max Arrest Force
≤
1800 lbs. (816.47 kg)
Max Arrest Force
≤
1800 lbs. (816.47 kg)
Average Arrest Force
≤
1350 lbs. (612.35 kg)
Average Arrest Force
≤
900 lbs. (408.23 kg)
Max Arrest Distance
≤
42 in. (106.68 cm)
Actual Arrest Distance
≤
23 in. (58.42 cm)
Actual Arrest Distance
≤ 23 in. (58.42 cm)
Use Below D-ring
Not permitted
Use Below D-ring
2 ft. (.61 m)
Max Free Fall Distance 24 in. (60.96 cm)
Max Free Fall Distance 48 in. (121.9 cm)
Inspection Log
Do Not Remove Label
J
F M A M J J A S O N D
DO NOT ATTEMPT TO SERVICE OR REPAIR THIS
UNIT! CONTACT SAFEWAZE FOR SERVICE OR
REPAIR INFORMATION. Device must be inspected
prior to each use in accordance with the manufacturer’s
instructions. Perform the locking function test (by pulling
sharply) and the retraction test. Inspect the device for
label legibility, any evidence of damage or defects, and
missing components or parts. Inspect all components of
device including the housing, connectors, fasteners, and
the entire length of the lifeline for any damage or
defects. Refer to instruction manual for inspection
frequency. Unit must be removed from service if
exposed to fall arrest forces. If visual fall indicator is
deployed, immediately remove unit from service.
WARNING:
This is a single user fall arrester device. Device must be inspected prior to each use.
Connection of this device to a full body harness is to be made to the dorsal D-ring only. User must
ensure that any connection to anchorage is properly secured prior to use. Make only compatible
connections. Dual connections shall only be used for 100% tie-off transitions. Refer to instruction
manual for minimum anchorage strength requirements. Not approved for leading edge applications,
anchor at or above D-ring only. Fall clearances must be calculated by a competent person prior to use.
Avoid swing fall hazards by working directly under anchorage. Avoid contact with sharp surfaces or
abrasive edges. Avoid chemical, thermal and/or electrical hazards. This product is suitable for use
horizontally and with horizontal lifelines. Adhere to the hierarchy of controls in Z359.2
USER MUST READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS
INCLUDED WITH THIS EQUIPMENT. DO NOT REMOVE LABEL.
If stitch pattern at the base of the housing
is torn open,
immediately remove
from service
PASS
FAIL
LOAD INDICA
TOR
OSHA
ANSI
1910.66, O
SHA
Z359.14,
ANSI
A10.32 1926.502
OS
HA
AN
SI
1910.
66,
OS
HA
Z359.
14,
AN
SI
A
10.
32
1926.
502
DO NOT USE
1 ft.
-1 ft. (-0.3 m)
0 ft.
0 ft. (0 m)
1 ft.
1 ft. (0.3 m)
3 ft.
3 ft. (0.9 m)
5 ft. (1.5 m)
NON-LEADING
EDGE
CLEARANCE
REQUIREMENTS
5’ 11”
(1.8 m)
Minimum required fall clearance:
5’ 11” (1.8m)
13
’ 1
1”
(4
.2
m)
2 ft. (0.6 m)
4 ft. (1.2 m)
2 ft.
4 ft.
2 ft.
11
’ 1
1”
(3
.6
m)
9’
1
1”
(3
m
)
7’
11
” (
2.
4
m
)
