Safer PR90 Maintenance Manual Download Page 101

Page: 101 / 112

Globalis International

PR9 SERVICE MANUAL-VER1.1 Page 101 of 112

cables (2) from the connectors on the printhead.

Fig. 6-5

6.3.7. PRINTHEAD PHOTOSENSOR DISASSEMBLY/REASSEMBLY

－

Remove the printhead (section 6.3.6).

－

Remove screw (1) that secures the printhead photosensor and remove
the photosensor from the ribbon protector.

－

Unplug the photosensor cable from its connector on the printhead.

6.3.8. PRINTHEAD CABLE DISASSEMBLY/REASSEMBLY

－

Remove the printer case (6.3.1)

－

Remove the printhead (section 6.3.6).

－

Lift the front part of the mechanical and unplug the 2 printhead cables
from the main board.

－

Free the 2 rear cable metal fastener and loose screw, then free the
printhead cables gently from underneath the mechanical.

－

Remove the printhead cable from the cable support,

Summary of Contents for PR90

















































































































Search results

Summary of Contents for PR90

Reviews:

Related manuals for PR90

Brands by name

Popular brands

Safer PR90, Maintenance Manual

Search results

Summary of Contents for PR90

Reviews:

Related manuals for PR90

Brands by name

Popular brands