background image

21

 

 

                 
  
                                                                                          
                                                                                                          

 

Ÿ

Testing Procedures with the TL305

1. Please wait for 10 seconds after power is connected. Check if Yellow LED is 

blinking

2. Turn on the TL305 and point it at the front of the SafeFlame. The recommended

distance between the test lamp and the detector is within 16ft(5m)

3. If the Red LED is on, the fire is detected
4. If the product is set to reset manually, cycle power to the detector
5. If the Red LED does not turn on, please reduce the testing distance and try 

again. If that same problem persists, check the test lamp for functionality. If 
working properly, contact the manufacturer. 

Note: If bulb No. 1 is blinking and the radiation intensity is weak, or if the No. 2 bulb is 

not functioning, please re-charge the test lamp. If neither the No. 1 or No. 2 bulbs
turn on, it means the test lamp is defective and require repair. 

Detector Status During Testing

Operational or Output Status

Before Connecting Power

-Fault Relay signal Open (N.O.: De-Energized)
- All LEDs off

Common

Normal

Fire

After

Connecting

Power

-Fault Relay signal Closed (N.C.: Energized)
- After 7 seconds of self-diagnosis test, LED intersect for 
  3 seconds (Yellow   Red   Yellow   etc) blinking

-All output, “Normal” signal (N.C.: Energized)
- Orange LED blinking (0.5Hz)

- All output “Fire” signal

Status

 

4.3 Testing

 

 

 

 

4.3.1

 

 

 Built-in-Test

The detector will automatically perform a self-diagnostic test every 12 hours. 

 

 

4.3.2

 

 

 Test Lamp

The TL305 generates specific IR3 radiation which can be detected by the SafeFlame 
detector series as a fire. It has an individual built-in internal power supply, making it 
portable with up to a 30 minute charge. 

[Figure 14] TL305 Test Lamp

Test Lamp for 

IR3 Flame Detector

Model

 

SafeFlame Installation and Operation Manual 

(Publication#: MA-SF200OM)

 

Summary of Contents for SafeFlame SF200A
























Reviews: