Safe Fleet PRIME DESIGN ASH-8033 Assembly Instructions Manual Download Page 8 | Manualshive

Page: 8 / 8

Safe Fleet PRIME DESIGN ASH-8033 Assembly Instructions Manual Download Page 8

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).

▪

TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING

8

Varies

M8 x 35MM

Flat Washer

M8 Lock Nut

Fig. A

5

CONDUIT MOUNTING

5.1

Place the Strobe Holder onto the Conduit Carrier and

attach using the supplied hardware.

Torque to

70 in-lbs

5.3

5.2

The Strobe Holder can be positioned

anywhere between the Conduit Carrier

Mounting Clamp and Conduit Lock

Latch as shown below in Figure A.

ASH-8033 ASSEMBL

Y

INSTR

UCTIONS

NOTE: Conduit is shown for illustrative

purposes only, and is not included with this

Accessory Light Holder Kit.

This Light Holder Kit contains only the parts

needed to retrofit one side. Order an additional

kit for the other side to add an additional

accessory light.

CONDUIT LIGHT HOLDER
INSTALLATION SEQUENCE

USAM-ASH8033-US01 Rev-B 0119

«
...
6
7
8

Summary of Contents for PRIME DESIGN ASH-8033









Reviews:

No comments