Saeco Tchibo Cafissimo HD8603, Operating Instructions Manual

Page: 34 / 88

• 24 •
CAPPUCCINO / FROTHED MILK /
LATTE MACCHIATO
Warning! Dispensing may be preceded by small jets
of hot water: danger of scalding! If the carafe is ab-
sent, products requiring milk should not be selected.
Cappuccino
Before brewing the cappuccino, check that the On/Off
button and beverage buttons are constantly lit
and that there is enough water in the tank.
1- To prepare a cappuccino, insert an espresso capsule (black) as
described in the section “Brewing coffee”.
2-
Insert the carafe into the machine and ensure that the milk is
above the MIN level.
3- Adjust the machine to fit the mug into which your cappuc-
cino will be dispensed (see section “Adjusting the dispensing
height”).
4- Insert a mug below the coffee and milk
dispensing spouts.
5- Press the Cappuccino button .
6-
The Cappuccino button flashes;
the machine is warming up.
7- When it has finished warming up, the
machine dispenses the frothed milk
directly into the mug. The machine
will stop dispensing when it reaches the preset quantity.
The dispensing process can be stopped early by pressing the
Cappuccino button .
8- When it has finished dispensing the milk, the machine
automatically dispenses the espresso coffee directly into the
mug. The dispensing process can be stopped early by pressing
the Cappuccino button .
When the cappuccino has finished brewing, the rinse
button will light up to remind you that the milk
circuit must be rinsed; see the section “Rinsing the milk cir-
cuit” in this chapter.
Adjusting the amount of cappuccino
The machine allows you to adjust the amount of cappuccino brewed
according to your taste and the size of your mug.
Before brewing the cappuccino, check that the On/Off
button and beverage buttons are constantly lit
and that there is enough water in the tank.
Proceed as follows to set the desired quantity of cappuccino :
1- Insert an espresso capsule into the appropriate compartment.
2- Insert the carafe into the machine and ensure that the milk is
above the MIN level.
3- Press and hold the Cappuccino button for 3 seconds until it
flashes in brief intervals. Then release the button.
4-
Press the Cappuccino button again when the amount of
milk in the mug reaches the desired level. The machine has
saved the desired amount of milk and will start to brew the
espresso.
5-
Press the Cappuccino button again when the amount of
coffee in the mug reaches the desired level. The machine has
saved the desired amount of espresso.
At this point the Cappuccino button has been reprogrammed;
each time it is pressed, the machine will disperse the same amount
of milk and espresso that was just programmed.
Minimum quantity of espresso that can be set: approx. 30ml
Maximum quantity of espresso that can be set: approx. 300ml
Minimum quantity of milk that can be set: approx. 50ml
Maximum quantity of milk that can be set: approx. 300ml
Preset quantities
Cappuccino approx. 90ml milk
approx. 40ml espresso
Restoring the pre-set quantities
To reset beverages to their factory settings, with the machine off,
press and hold the On/Off and Filter coffee (blue) buttons
for 5 seconds. All the buttons will flash twice in confirmation.
Frothed milk
Before preparing the frothed milk, check that the
On/Off button and beverage buttons are con-
stantly lit and that there is enough water in the tank.
Remember, it is not necessary to insert any coffee
capsule in order to prepare frothed milk.
1- Insert the carafe in the machine and ensure that the milk is
above the MIN level.
2-
Adjust the machine to fit the glass
into which your frothed milk will be
dispensed (see section ''Adjusting the
dispensing height'').
3-
Place a glass under the milk dispensing
spout.
4- DO NOT insert a coffee capsule into the
capsule compartment.
5- Press the Frothed milk button .