3501-0232/0233I HD Dyna 91-95 Rev 03/08
READ ALL INSTRUCTIONS THOROUGHLY BEFORE STARTING!
You are responsible for the correct installation and safe use of this bag. Seek qualified instruction if you are
uncertain about its capabilities and limitations or if you need help with installation. Use of the bag in a
manner other than its intended purpose or contradictory to the warnings and instruction provided could
cause loss of control of your motorcycle, possibly resulting in personal injury or death.
??
You must mount saddlebags properly and securely before riding motorcycle. Failure to do so could
result in damage to the saddlebag and motorcycle.
??
Do not use these bags if the mounting system has deteriorated, loosened or is beginning to fail
??
Do not exceed maximum weight of 10 lbs per saddlebag.
??
DO NOT ATTEMPT TO USE THESE SADDLEBAGS IF....
??
...you do not understand these instructions;...you do not understand any part of the mounting system;
??
...you have any doubts as to the security of the mounting system.
??
If you have any doubts or questions, SEEK PR OFESSIONAL HELP at your qualified motorcycle
dealer or call Saddlemen at 310-638-1222.
Motorcycling is an inherently dangerous activity. Installation of any accessory, including
saddlebags, can add to the danger if they are not installed safely. You must install them in a
manner in which they will not contact any part of the drive train, suspension or steering, or interfere
with any operation of the motorcycle. If you do not know how to do this, or have any doubts as to
your ability, please have a qualified motorcycle mechanic install them.
PARTS LIST
2- Saddlebags
2-Saddle Bag Supports 2- Studs5/16x2 1/2 2- Studs3/8x3 2- 5/16 Docking Posts 2- 5/16 Lock Nuts 2-3/8 Docking posts 2-3/8 Lock Nuts 2
Chrome Spacers 2-Turn Signal Brackets 2-Black Wires 2-Green Wires 8- Butt Connectors 2- Hex Nuts 5/16-18 2- Socket cap screws 1/16-18x3” 4-1/4 Turn Bag
Locks 2- Pad Locks with Keys 2 Keys for Q.R. Buckles 1 – Instructions
INSTALLATION INSTRUCTIONS
WARNING: To avoid injury, install while engine is cold. Disconnect the battery.
We recommend relocating one side at a time, completing one side before starting on the other side. This will
help maintain fender alignment, and give you a reference for wire routing Etc.
1). Remove tail light lens.
2) Trace wires from turn signal lights and unplug form tail light terminal.
3) Push wires back through the fender holes, and free them from clips, etc, to the turn signal lights. Be careful to
note the routing of the wires so you can re-rout them in the same way when you reassemble the light.
4) Remove the bolt holding the turn signal light and carefully remove the wire thru the hole.
5) Cut the wires 1½ inch from where they exit from the turn signal support.
6) Strip 3/8inch insulation from the ends of the turn signal wires, and both ends of all the extension wires
supplied.
7) Using a crimping tool, and the butt connectors, add an extension wire to the end of each turn signal wire
only, black to plain wire and the green to the striped wire (you will splice the connector ends after routing the
wires through the turn signal brackets).
8) The Turn Signal brackets are disassembled. Each is made up of a thick plate, a black center part, and a thin
outer plate. Remove the paper from one side of the black center part, align and press to the thick inner part with
the tang away from the black center part.
9) Rout the wires from the turn signal through the oval hole at the small end of the thin center part, polished
side toward the turn signal, then and out the last hole in the opposite side (with the tang).
10) Neatly arrange the wires in the center grove, remove the protective paper from the center part align and
press together.
11) Loosely install the turn signal with the 5/16-18x3” bolt supplied to hold the turn signal in place on the
bracket.
RIGID
SADDLEBAG
RIGID SADDLEBAG INSTALLATION INSTRUCTIONS
17801 S. Susana Rd.
Rancho Dominguez, CA 90221
(310) 638-1222 Fax (310) 761-1234
www.saddlemen.com
WARNING:
!
