Sabo 36-ACCU Operator'S Manual Download

Page: 36 / 88

All models

PREPARATION

The following unit parts are included in the package for mower assembly:

•

Mower with pre-assembled handlebar

•

Grass catch, collecting bag frame, sloped channel

•

Battery

•

Charger

•

Tool bag containing the following:

–

Operating instructions with Declaration of Conformity

–

Guarantee conditions (depending on the model)

–

Diverse attachment parts.

Should a part be missing, please contact your professional dealership.

Raise the handlebar (Illustration A1 + O4 + B1 )

IMPORTANT
Make sure that the cables are not pinched, squeezed, twisted or overstretched
when the handlebars are folded apart or collapsed! Always run the cables along
the outside of the bar connection. A damaged cable may result in a technical
defect of the equipment.

40-ACCU

NOTE

Before the handlebars are raised, the cutting height must be set to position 3 (40 mm)
or higher

. The handlebar cannot be pivoted backwards completely in the two lower

cutting positions.

All models

–

Pull the handlebar which is collapsed in a Z-shape upwards into place

–

When the top and bottom parts of the handlebar are on the same level, firmly

tighten the wing nuts by hand

–

Pivot the bottom part of the handlebar backwards until the toothed plastic fitments

lock into place at the lower end in the toothed recess on the mower housing.
Three different handlebar heights can be set

–

Tighten the wing nuts on both sides by hand

–

Insert the cable in the cable guide and fix on the top and bottom part of the

handlebar using the cable ties from the tool bag

. Route the cable along the

outside of the handlebar to ensure the ejector flap can still remove freely during
raising and closing.
When folding the top part of the handlebar over, make sure that the cable can
move freely.

CAUTION
When you activate the bar height adjustment, when loosening the wing nuts

used to secure the bar bottom to the housing (only loosen sufficiently to

ensure that the bar can be moved freely) and snapping the toothed plastic
adaptations from the cut-out on the housing, it is possible that unintentional
upsetting of the bar may occur. In addition, this may result in crushed points
between the bar bottom and the housing. This may result in a risk of injury!

Assemble the collecting sack and hang it onto the mower

(Illustration Q1 + R1 + S1 )

36-ACCU

–

Remove the attached fixing panels from the chute

–

Set the chute into the collecting bag frame at an angle. By moving the chute down

press the holding bracket on either side onto the collecting bag frame

–

Then press the lower holding brackets of the chute onto the transverse rod of the

collecting bag frame.

–

Screw the two fixing panels to the chute again

–

First insert the grass bag frame with the clip forward into the grass bag. Align the

upper seams of the bag with the clip.

–

Press the retaining profiles of the collecting sack onto the bars of the collecting

sack frame

–

Open the ejection flap of the mower upwards.

–

Pick up the collecting sack by the carrying strap, place the chute (1) at the

collecting sack opening into the ejection flap and hang it in the mower casing with
its two side hooks upwards

–

Attach ejection flap to collector.

40-ACCU

–

Press the lateral retaining clip (2) of the chute (1) onto the collecting bag

frame

–

From below, hang the bar (3) of the crossbar into the chute.

–

Then press the lower retaining clips (4) onto the crossbar of the collecting bag

frame.

–

First insert the grass bag frame with the clip forward into the grass bag. Align the

upper seams of the bag with the clip.

–

Press the retaining profiles of the collecting sack onto the bars of the collecting

sack frame

–

Open the ejection flap of the mower upwards.

–

Pick up the collecting sack by the carrying strap, place the chute (1) at the

collecting sack opening into the ejection flap and hang it in the mower casing with
its two side hooks upwards

–

Attach ejection flap to collector.

43-ACCU

–

Insert the collection bag frame with the bar first into the grass catch. Align the

upper seams of the grass catch on the bar.

–

Press the holding profile onto the frame of the collection bag frame

–

Open the ejection flap of the mower upwards.

–

Lift the grass collection bag on the carrier bar, insert the chute (1)

on the

collection bag opening into the ejection flap and hang the grass collection bag with
the two side hooks to the top of the mower housing

–

Fold the ejection flap onto the grass collection bag.

Adjusting the cutting height (Illustration I )

Safety instruction!

See table for explanation of symbols page 3

36-ACCU

The mower is adjusted to the lowest cutting height upon delivery.

–

The cutting height is set on the left hand side of the lawnmower

–

Press the red button with your thumb and move the handle of the lawnmower into

the required position by moving it up or down.

–

By letting go of the button, the lever locks into the required cutting height.

–

The marking on the left on the adjusting rod indicates the cutting height.

40-ACCU, 43-ACCU

The cutting height is adjusted behing the motor.

–

Press the grey push button with your thumb and lift or lower the mower handle to

bring it into the required position.

–

Release the push button: the lever now engages in the required cutting height.

–

The marking on the left of the housing shows the adjusted cutting height.

All models

IMPORTANT
Mowing at the lowest cutting height should only be carried out on level and plane
lawns!
Please observe that the lower cutting height settings may only be used for
optimal conditions. If you select cutting height that is too low, the turf can be
damaged and under certain circumstances it can even be destroyed.
Besides the cutting height, also the moving speed influences the cutting pattern
and collection result. Adapt the cutting height and moving speed to the grass
height to be cut.

Insert the charged battery (Illustration K2 + V1 + G2 )

The handling of the charger and battery is described in
the separate operating instructions for the charger.
In particular, read and note the safety information!
Fully charge the battery before initial use!

–

Open the battery cover and keep hold of it.

–

Remove the safety key

–

Push the battery into the battery compartment until it locks into place

Make sure that the locking device on the battery is freely accessible and locks
cleanly into place.

–

Insert the safety key if the mower is to be used immediately

–

Close the battery cover. Make sure that the cover closes automatically. Dirt and

grass cuttings can prevent this and must be removed for this reason.