background image

Fig 1:

        Figure 1 shows the motor correctly 

wired. It is advisable to cover the wire 

joints between the motor and the ESC  

with heat shrink tubing.

  2 mm  

  0.75 mm  

  0.75 mm  

Big Motor Belt

(HC309-S)

MOTOR BELT TENSION

*Assemble the motor and pinion to its mounting plate.

*Fit the motor assembly into position.

*Compress the springs by pushing the motor toward the main shaft.

*At maximum compression, temporarily tighten one of the slide screws.

*With the minimum centre distance it is easy to install the belt. First put the belt on the motor pinion.

*Then put the belt around the big pulley.

*Rotate the motor several times by hand.

*Release the screw that locks the slide.

*The springs keep the belt in tension.

*Help the springs by pulling the motor slightly.

*The belt must be very tight.

*Lock all screws.

Motor Assembly

Note: 

      

 

Check for vertical alignment of 

the motor pulley. To do this, simply 

turn the motor several time and 

check to you see if the belt is aligned 

with the big pulley ( one way bearing 

pulley ). If the belt is riding too high, 

simply loosen up the motor pulley 

and drop it just a little bit, if it is 

riding too low, loosen up the motor 

pulley and raise it a bit.

Correct

Incorrect

FOAM 2

Page 18

Chapter 9, Installation Of The Motor

Summary of Contents for Goblin 700













































Reviews: