S+S Regeltechnik RYM7-10IB-2102-000 Operating Instructions Manual Download Page 2

S+S  REGELTECHNIK GMBH  |  THURN-UND-TA XIS-STR. 22  |  D-90411 NÜRNBERG  | GERMANY |  FON +49  (0)  911 51947- 0  | w w w.S plusS.de

2

Operating instructions 

RYM

ASKON

®

    700 - BACnet 

RYM

ASKON

®

    700 - Modbus

INSTALLATION AND  
COMMISSIONING

IMPORTANT NOTES

Only the valid edition of our conditions and the valid “General Conditions for the Supply of 
Products and Services of the Electrical and Electronics Industry” (ZVEI conditions) and 
the supplementary clause “Extended Retention of Title” apply as the terms and conditions 
regulating this purchase.

The following points must also be complied with:
- These instructions must be read before installation and commissioning,  

and all of the specifications that they contain must be complied with.

-  The units must only be connected to an extra-low safety voltage in a de-energised condition.  

Use shielded cables to avoid damage to the unit and faults (e.g. resulting from voltage induction),  
avoid parallel routing with live lines, and comply with the EMC directives.

-  This unit must only be used for its intended purpose, whereby the applicable VDE safety regulations and 

all regulations issued by the regional and national regulatory authorities, TÜV and local energy providers 
must be complied with. The purchaser must ensure that the relevant building and safety regulations are 
complied with, and must avoid hazards of all kinds.

-  No warranty or liability whatsoever will be accepted for defects and damage arising from improper 

use of this unit.

-  The warranty and liability excludes consequential damage caused by a fault in this unit.
-  The units must only be installed and commissioned by qualified personnel.
-  Only the technical data and connecting conditions specified by the installation and operating instructions 

which are included in the scope of delivery of the unit apply. Deviations from the depictions contained in 
the catalogue are not additionally listed, and are possible as a result of technical progress and the 
continuous improvement of our products.

-  Any alterations made to the unit by the user will void the warranty.
-  This unit must not be installed close to sources of heat (e.g. radiators) or their heat flow. Avoid direct 

solar irradiation or heat radiation from similar sources (powerful lamps, halogen spotlights).

-  Operating this unit close to other devices that do not comply with EMC directives may influence the 

functionality thereof.

-  This unit must not be used for monitoring purposes which serve the purpose of protecting persons 

against hazards or injury, as an Emergency Stop switch on systems or machinery, or for any other 
similar safety-related purposes.

-  The housing dimensions and the dimensions of accessories may differ slightly from the specifications 

of these instructions.

-  Changes to these documents are not permitted
-  In cases of complaint, we will only accept complete units returned in their original packaging.

Commissioning is mandatory and may only be performed by qualified personnel! Please read these instruc-
tions prior to installation and commissioning, and comply with the specifications that they contain!

Mounting shall take place while observing all relevant regulations and standards applicable for the place of 
measurement (e.g. such as welding instructions, etc.). It is particularly important to comply with the 
following:

-  VDE ⁄ VDI technical temperature measurements, directives, measurement set-ups for 

temperature measurements.

-  EMC directives
-  It is imperative to avoid parallel routing of current-carrying lines
-  We recommend the use of shielded cables with the shielding attached to the DDC/PLC at one side.

Before mounting, make sure that the existing technical parameters of the measuring instrument comply 
with the actual conditions at the place of utilization, particularly with regard to:

-  the measuring range
-  the maximum permissible temperature and humidity
-  the protection type and protection class
-  oscillation, vibration and impacts must be avoided (< 0.5 g)

Devices with integrated CO2-Sensor

Devices with integrated CO2-Sensor have 

an automatic calibration of the carbon dioxide measurement – 

ABC logic.

 The Automatic Background Logic is a self-calibrating mechanism that is suitable for use in 

applications in which the CO2 concentration regularly drops to fresh air level (350 - 500 ppm).  
This should typically happen at times during which the rooms are unoccupied.  
The sensor reaches its normal accuracy after 24 hours of continuous operation in an environment which 
has been exposed to a fresh air supply of 400 ppm CO2. The deviation error remains minimal with at least 
4 cases of sensor exposure to fresh air within 21 days. The ABC logic requires continuous operating 
cycles of longer than 24 hours in order to function properly.

2

Summary of Contents for RYM7-10IB-2102-000































Reviews: