background image

9

S T A N D - A L O N E   E N V I R O N M E N T   &   O P E R A T I O N 

I N S T A L L I N G   T H E   P T - 6 0 0 2   U N I T   T O   T H E   P T - B A S E 

TOGGLE SWITCH OPERATION

The PT-6002 input will be connected to un-switched line voltage (through NEC appropriate GFCI breaker) 

and can be operated manually by the on-board, 3-position switches or the included hand-held remote control.

Manual Operation

The channel is operated by a 3-position switch. To turn on, move the power switch to the upper, on position. 

To turn off, move the power switch to the middle, off position.   

Remote On/Off Operation

Move the power switch to the lower, remote position and use the hand held remote to toggle the low voltage 

power circuit on and off. 
See below for remote button functions and features.

1.  Place the chassis on the installation base (from previous installation or purchase of optional 

 

part PT-BASE).

2.  Adjust the incoming 120V cable and all 12V outgoing cables to remove unnecessary loops and/or kinks.
3.  Secure the PT-6002 unit to the PT-Base using the two supplied sheet metal screws.  
4.  Make sure that the 3-position switches are in the off (middle) position.  
5.  Place top cover onto unit and secure with the two supplied machine screws.

Circuit #1

ON

Circuit #1

OFF

Circuit #1

REMOTE

Circuit #2

ON

Circuit #2

OFF

Circuit #2

REMOTE

Summary of Contents for Power Tower PT-6002













Reviews: