S.I.T.A. 400 Series Manual Of Installation, Use And Maintenance Download Page 31

 

30 

12.

 

Warranty Condition 

 

WARRANTY CONDITIONS  

    

 

SITA works in compliance with ISO 9001-2008 quality procedures and subjects all equipments to 
accurate checks and tests. 
The  SITA  supplies  and  progressing  are  anyway  guaranteed  only  in  the  limits  of  technical 
specifications  and  request  and/or  of  the  certificates  and/or  of  the  specific  checks  as  agreed, 
for 24 months from the purchase date, provided that eventual defects are stated as fixed by 
art. No. 1495 of the civil code. 
The  stainless  steel  chamber  is  covered  by  warranty  of  5  years  only  if  used  for  compatible 
liquids and correctly installed. 
In  no  case  the  integral  replacement  of  the  product  is  forseen  and  any  responsibility  of  sita  is 
excluded for delays in the delivery of the goods to the customer, for claims of third parties towards 
the customer, for losses of goods, costs (installation, servicing and maintenance, transports, and so 
on) and damages of the customer due to the defect. 
Moreover  the  product  repaired  or  tampered  by  non-authorized  third  parties,  and  the  product  on 
which  an  intervention  has  been  made  for  defect  of  for  convenience  tests,  is  excluded  from  the 
warranty. 
Repairs  are  normally  carried  out  in  SITA  warehouse  or  in  authorized  after-sales  service  centers 
signalled by SITA. 
 
The warranty does not cover: 
1.

 

Accidental breakages due to the transport. 

2.

 

Breakages  due  to  the  use  of  equipments  not  in  compliance  with  what  is  indicated  on  the  use 
and maintenance manual or to carelessness. 

3.

 

Breakages to the connection to a power grid feeded with a tension different than the foreseen 
one (±10% of the nominal value as fixed by CEI rules) 

 
DO NOT TAMPER THE ADHESIVE LABELS OF IDENTIFICATION 
 

The  adhesive  label  with  the  QC  (Quality  Control)  number  must  be  intact  and  readable;  such 
number allows to enter the data bank of tests and to find the values obtained in the electrical test of 
the equipment. 
The adhesive label with the S/N (Serial Number) number must be intact and readable; such number 
allows  to  enter  the  data  bank  of  tests  and  to  find  the  values  obtained  in  the  hydraulic  test  of  the 
equipment. 

       In case of dispute the court of Genova will be competent. 
 
 

 

 
 
 
 
 
 

Summary of Contents for 400 Series

































Reviews: