S.& A.S. OMEGA-ATS User Manual Download Page 30 | Manualshive

Page: 30 / 46

S.& A.S. OMEGA-ATS User Manual Download Page 30

8.

Disconnect the USB cable.
If you desire to delete any SAS file from the mobile list, press on the filename until a Popup window
appears showing you multiple choices and then click on Delete.

4.3 ONLINE FIRMWARE UPGRADE

In order to upgrade firmware remotely, the OMEGA must be connected to the internet and its status
must be online & the below steps shall be followed:
1.

Run the OMEGA Web application on our website

www.sascontrollers.com\Omega

.

2.

Enter the username and the correspondent password to access your already registered account.

3.

A list of your OMEGA controllers appears (see the figure below).

4.

Check Controller Ver. and Eth. Ver. of the OMEGA to see if any upgrade is needed.

5.

To upgrade the OMEGA, make sure the gensets are turned off, and then click on the button “Firmware
Upgrade”

6.

The user is prompted to enter a password. This password is provided by S. & A. S. Ltd.

7.

The below window appears if the valid password is entered.

4. FIRMWARE

UPGRADE

«
...
28
29
30
31
32
...
»

Summary of Contents for OMEGA-ATS















































Reviews:

No comments